Все товары
-
CAHOZA 3 COIL SPRINGS STAINLESS STEEL, pair - #254
3 COIL SPRINGS
Cahoza springs for G12, Cobalt 12, INT15 motors, made from stainless steel, resists up to 800F, these springs have got the same tension as Red Champion, but the quality and workout is far more professiona -
KOFORD Ultrastrong radial C-Can drag magnets- #M592
KOFORD Ultrastrong radial C-Can drag magnets
Ultrastrong radial drag magnets, when used with M593 treated can produces 4% more flux then competitors wide can and .170 thick quad magnets without the problems of nonstandard size cans. .165 thick x .520 long
-
PROSLOT Purple dot MegaMaster 6-mag magnets - #PS-909S
PROSLOT Purple dot MegaMaster 6-mag magnets - #PS-909S
Magnets only!
-
B52 C-Can Combo magnets 0.167" thick, 0.458" long, type 1 (one side is flat one side is bevelled), pair
B52 C-Can magnets, type 1, pair
-
B52 C-Can Flat magnets 0.167" thick, 0.458" long, type 2 (both side is flat), pair
B52 C-Can magnets, type 2, pair
-
CAHOZA Single endbell for C-Cans (G-12) - #126
CAHOZA Single endbell for C-Cans (G-12)
Aluminium hard anodised single endbell for G12 Cahoza C-cans, lightened, pattern hole drilled for hardware #170 and #171
-
CAHOZA Assembled endbell for G12 C-Cans - #146
CAHOZA Assembled endbell for G12 C-Cans
New aluminium hard anodised assembled endbell for all Cahoza C-cans (G12), gold plated horizontal hardware (#171), 3coil aluminium spring posts, includes stainless steel ball bearing, diameter for cans is 21,25mm (.837"), this endbell is made from very hard aluminium, perfectly dissipates heat away from brushes
-
CAHOZA Assembled endbell for G12 C-Cans +4° rotation - #146-H4
CAHOZA Assembled endbell for G12 C-Cans +4° rotation
New aluminium hard anodised assembled endbell for all Cahoza C-cans (G12), gold plated horizontal hardware (#171) turned to +4°, 3coil aluminium spring posts, includes stainless steel ball bearing, diameter for cans is 21,25mm (.837"), this endbell is made from very hard aluminium, perfectly dissipates heat away from brushes
-
PROSLOT Magnet Clips for C-cans,1 pc. - #PS640
PROSLOT Magnet Clips for C-cans, 1 pc.
This is the clips for all 12-group (C-cans) motors.
-
PROSLOT HARDWARE FOR PROSLOT MOTORS X-12 GROUP, W/SPRING CUPS & SCREWS- #PS642
Hardware set complete -includes hardware, oilite, spring cups and screws
-
PROSLOT BRUSH HOOD/ HEAT SINK SET FOR PROSLOT MOTOR (X-12 GROUP), W/OUT SPRING CUPS & SCREWS- #PS641
Brush Hood & Heat Sink set
-
PROSLOT Velociraptor VR 12 “NEO” motor - #PS-4019
PROSLOT Velociraptor VR 12 “NEO” motor
This motor uses the new PS-4017 “Neo” Euro MK1 setup with a specially made .500 diameter VR12 machine wound armature on our race proven Intruder blank and includes G7 brushes. This motor was built for the new wave of “NEO” F/C racing. Our testing using an 85 gram hardbody test car netted .720 ET’s @ 70+ MPH. Recommended starting gear ratio 14/52.
-
CAHOZA Tapping screw for Allen head wrench, 1 pc. - #272
CAHOZA Tapping screw for Allen head wrench, 1 pc. - #272
-
CHAMPION Super wasp motor - #CHA509HTX
CHAMPION Super wasp motor - #CHA509HTX
SUPER WASP Motor (Champion) - Balanced/High Timed 42 Degrees - .350" Stack / 60T / 30 Gauge Wire
-
PROSLOT SpeedFX 16D/S16D SETUP - #PS 2004
FX 16D/S16D Motor Setup
-
PROSLOT 16D/S16D MOTOR CAN - #PS2005
Proslot can for 16D motors, w/out magnets
-
PROSLOT SPEED FX S16D BLUEPRINT SETUP, W/MATCHED MAGNETS - #PS 2100
SpeedFX 16D/S16D Blueprinted Setup with Matched Magnets. The setup includes straightened can, soldered oilite, aligned and honed brush hoods and matched magnets.
-
PROSLOT Velociraptor VR eXtreme “NEO motor - #PS-4021
PROSLOT Velociraptor VR eXtreme “NEO motor
This motor uses the new PS-4017 “NEO” Euro MK1 setup with a specially made .500 diameter VR eXtreme machine wound armature on our race proven Intruder blank and includes G7 brushes. This motor was built for the “Ultimate” bracket racer and “Outlaw NEO” class racer. Our testing using an 85 gram hardbody test car netted .590 ET’s @ 90+ MPH. This motor has no equal in performance for the money. Recommended starting gear ratio 14/54
-
PROSLOT Velociraptor VR Open “NEO” motor - #PS-4025
PROSLOT Velociraptor VR Open “NEO” motor
This motor uses the new PS-4017 “NEO” Euro MK1 setup with a specially made .500 diameter custom hand wound all-out Topgun style armature featuring our EDM commutator, wound on our race proven Intruder blank and our copper hardware on the endbell. Standard wind 18/24.5 and double ball bearings. Also available in 25/25, 15/24, 14/24
-
JK Set-up For JK#M3 HAWK w/Ceramic Magnets - #M3S
JK Set-up For JK#M3 HAWK w/Ceramic Magnets - #M3S
Only HAWK motor with special armature (marked RUS) may be used in Production 1/32 by russian rules
Old catalog #JK30301
-
-
JK REPLACEMENT ENDBELL FOR HAWK #M3 (#M6), ALUMINIUM - #M3EA (#M6EA)
JK REPLACEMENT ENDBELL FOR HAWK #M3 (#M6), ALUMINIUM - #M3EA (#M6EA)
New improved - Upgraded Aluminum endbell for JK Hawk #M3 motors
Only HAWK motor with special armature (marked RUS) may be used in Production 1/32 by russian rules
Old catalog #JK30303AL
-
JK NEODYMIUM MAGNETS FOR HAWK MOTOR - #M3M (#M6M)
JK NEODYMIUM MAGNETS FOR HAWK MOTOR - #M3M (#M6M)
NEODYMIUM REPLACEMENT MAGNETS FOR HAWK 3030 MOTOR (more powerful than stock)
Only HAWK motor with special armature (marked RUS) may be used in Production 1/32 by russian rules
-
JK Motor Screw 6mm 0.050" Allan Head Black, 6 pcs. - #M52
JK Motor Screw 6mm 0.050" Allan Head Black, 6 pcs. - #M52
Old catalog #JKS03