CAHOZA

• 

  CAHOZA Ø2 mm AXLE (length 55 mm) - #24

  SOLID AXLE 2MM
  solid 2mm axle, highly durable 60HRc, axle is very fine grinded and polished, the 2mm diameter is very accurate with maximum deflection of 0,001 mm (.00004"), great straightness along the entire length, it is crooked to max. 0,005 mm (.0002") throughout the entire length, ends are also grinded, exact diameter of this axle is 1,992mm (.07838"), length is 51mm (2") the best axle ever available for Scale racing

  5.20 $

• 

  CAHOZA ALUMINUM ANODISED SPRING POST /3 COIL,1 pair - #154

  ANODISED SPRING POSTS - 3 COIL SPRINGS
  aluminium anodised spring posts for 3 coil springs, spring post do not fit Cahoza plastic G12 endbells, suitable for hardware #170 and #171, packaged 10 pairs per bag

  3.50 $

• 

  Cahoza black covered pinion 72 pitch 5 teeth, 0° angle 1.2 mm bore - #17A

  34.00 $

• 

  CAHOZA Low profile cut down nylon elastic guide, w/out thread - #26

  cut down guide for integral guide tongue chassis, content: blue nylon, glass fibre, these guides have minimum content of glass fibre for higher elasticity, ideal for Production chassis

  2.15 $

• 

  CAHOZA CUT DOWN GRAPHITE GUIDE, non thread - #28

  CUT DOWN GRAPHITE NYLON GUIDE
  cut down guide for integral guide tongue chassis, content: black nylon, glass fibre, graphite

  
  

  2.15 $

• 

  CAHOZA ARM SPACER BRONZE .004", 24 psc. - #36

  PHOSPHOR BRONZE SPACERS 0,1
  phosphor bronze spacers, thickness 0,1 mm (.004"), ultra precision fit on armature shaft to eliminate vibration due to loose fit, phosphor bronze is very hard, but will not stick to magnets, packaged 24 per bag

  5.20 $

• 

  CAHOZA C CAN TYPE "UL" - #252

  C-CAN TYPE UL
  Cahoza C-can, produced from 0,4mm (.0157") thick hardmetal plate

  39.00 $

• 

  CAHOZA ANODIZED 5 COIL SPRING POSTS, 1 pair - #157

  ANODISED SPRING POSTS - 5 COIL SPRINGS
  aluminium anodised spring posts for 5 coil springs, avaliable in red-blue and red-black combinations, suitable for hardware #170 and #171, packaged 10 pairs per bag

  4.90 $

• 

  CAHOZA Gear 64 pitch, 35T, 0° angle, 3/32" axle, Ø14.65 mm - #6

  CAHOZA Gear 64 pitch, 35T, 0° angle, 3/32" axle, Ø14.65 mm - #6

  Polymer gears 64 pitch, for 3/32" axle, but only selected ones, high quality and accuracy, for demanding racers, tested on our roll tester,

  4.90 $

• 

  CAHOZA M1 Screw & Insulator, 1 set - #113

  CAHOZA M1 Screw & Insulator, 1 set

  stainless steel M1 screws, for endbells F1/32 and Sport 32, including insulators

  2.00 $

• 

  CAHOZA С-Can G12 motor - O - #230

  Cahoza C-can motor, assembled using:

  • "O" type C-can #250, 
  • Cahoza Tornado 2 magnets, 
  • Cahoza plastic endbell, 
  • Cahoza hardware #266, 
  • Cahoza aluminium spring cups, 
  • Cahoza tapping screws, 
  • Koford flanged oilites, 
  • Koford armature M468 -- Box TriStar G12 dia .518", perfectly balanced with shortened axle and cut down commudator, 
  • Koford brushes M486, 
  • Cahoza springs #257, 
  • magnets are glued in using Cahoza single component epoxy, 
  • inside diameter of magnets is 13,45mm (.529"), 
  • weight of complete motor is only 19,2 grammes.

  100.70 $

• 

  CAHOZA C-Can G12 motor - O - bevelled - #230B

  Cahoza C-can motor, assembled using:

  • "O" type C-can #250, 
  • Cahoza Tornado 2 bevelled magnets #276,
  • Cahoza plastic endbell, 
  • Cahoza hardware #266, 
  • Cahoza aluminium spring cups, 
  • Cahoza tapping screws, 
  • Koford flanged oilites, 
  • Koford armature M468 -- Box TriStar G12 dia .518", perfectly balanced with shortened axle and cut down commudator, 
  • Koford brushes M486, 
  • Cahoza springs #257, 
  • magnets are glued in using Cahoza single component epoxy, 
  • inside diameter of magnets is 13,45mm (.529"), 
  • weight of complete motor is only 18,2 grammes.

  105.70 $

• 

  CAHOZA PHENOLIC INSULATORS, 1 pc. - #158

  PHENOLIC INSULATORS
  phenolic insulators, use on all aluminium endbells

  0.24 $

• 

  CAHOZA Phenolic insulators, ID 1,5 mm, OD 3 mm, thick. 0,5 mm, 24 pcs. - #158

  CAHOZA Phenolic insulators, ID 1,5 mm x OD 3 mm x thick. 0,5 mm, 24 pcs. - #158

  phenolic insulators, use on all aluminium endbells, suitable for anodised spring posts #154, #157, inside diameter 1,5mm, outside diameter 3mm, thickness 0,5mm, packed by 24pcs

  6.70 $

• 

  CAHOZA ARM (2 mm) SPACER BRONZE .007" (0,18 mm), 24 psc. - #37

  PHOSPHOR BRONZE SPACERS 0,18
  the same as #36, but thickness is 0,18mm (.007"), packaged 24 per bag

  5.40 $

• 

  CAHOZA GEAR 72 PITCH 41T, 16° angle, 3/32" axle, Ø15.05 mm - #4

  CAHOZA GEAR 72 PITCH 41T, 16° angle, 3/32" axle,  Ø15.05 mm - #4

  5.20 $

• 

  CAHOZA highly durable gear 72 pitch 38 teeth, 0° angle, 3/32" axle, Ø14.52 mm - #5B

  CAHOZA highly durable gear 72 pitch 38 teeth, 0° angle, 3/32" axle, Ø14.52 mm

  6.20 $

• 

  CAHOZA highly durable gear corrected 72 pitch 38 teeth, 0° angle, 3/32" axle, Ø14.52 mm - #5BC

  CAHOZA highly durable gear corrected 72 pitch 38 teeth, 0° angle, 3/32" axle, Ø14.52 mm

  6.20 $

• 

  CAHOZA Light braid, 408 strands, .023" thick, 1 pair - #340

  CAHOZA Light braid, 408 strands, .023" thick, 1 pair - #340

  these braids size is 4.5 x 0.6 x 30 mm (.177" x .023" x 1.181"), 408 strands, made from very pure copper (99.9 %), these braids are ideal for PR24, ES24, SP32 and F1/32, they will last longer, the production process is finalized by Cahoza (handmade)

  2.50 $

• 

  CAHOZA Medium braid, 552 strands, .027" thick, 1 pair - #341

  CAHOZA Medium braid, 552 strands, .027" thick, 1 pair - #341

  these braids size is 4.8 x 0.7 x 30 mm (.188" x .027" x 1.181"), 552 strands, made from very pure copper (99.9 %), these braids are ideal for PR24 and ES24, they will last longer, the production process is finalized by Cahoza (handmade)

  2.50 $

• 

  CAHOZA Heavy braid, 624 strands, .031" thick, 1 pair - #342

  CAHOZA Heavy braid, 624 strands, .031" thick, 1 pair - #342

  these braids size is 5.0 x 0.8 x 30 mm (.196" x .031" x 1.181"), 624 strands, made from very pure copper (99.9 %), these braids are ideal for wing cars, they will last longer, the production process is finalized by Cahoza (handmade)

  2.50 $

• 

  CAHOZA Pinion 64 pitch, 7T, 0° angle, 2 mm bore, special black cover - #12

  CAHOZA Pinion 64 pitch, 7T, 0° angle, 2 mm bore, special black cover - #12

  GT1 64 pitch pinions for 2mm shaft, 7T, plated with special black cover especially developed for Cahoza, this cover enhances lubricity 8 times and repels solder so teeth cannot be soldered through, higher resistance

  12.00 $

• 

  CAHOZA Gear 64 pitch, 36T, 0° angle, 3/32" axle, Ø15.02 mm - #6

  CAHOZA Gear 64 pitch, 36T, 0° angle, 3/32" axle, Ø15.02 mm - #6

  Polymer gears 64 pitch, for 3/32" axle, but only selected ones, high quality and accuracy, for demanding racers, tested on our roll tester,

  4.90 $

• 

  CAHOZA G12 C-Can setup type UL - bevelled - #242-ULB

  Cahoza C-can setup, assembled using:

  • Cahoza C-can #252, 
  • Cahoza Tornado 5 bevelled magnets, 
  • Cahoza endbell #262, 
  • Cahoza spring cups, 
  • 2x5 precisely turned oilite in endbell, ball bearing in can, 
  • Cahoza screws,
  • for .518" armatures, Koford ones are recommended, 
  • professionaly assembled, 
  • weight 10.8 grammes

  112.40 $