MID AMERICA Ø3/32" (2.36 mm) rear axle, length 2.25" (57.15 mm), drill blank center flat - #MID520CF

3/32 Inline flatted drill blank axle for retro or drag racing. 2.25" long with center flat for gear.

KOFORD Ø3/32" (2.36 mm) Narrow flatted ultra-precision axle - #M744

Precisely ground flats to eliminate spinning and provide perfect dynamic balance. Special steel for twice the strength of drill blank axles and better rust resistance then other unplated axles

KOFORD EDM drilled/wire cut .060" hollow 3/32" rear axle - #M697F

EDM drilled and wire cut flatted .060 hollow race axle. Lighter and 50% stronger the M445F

VITULA bushings in production chassis, pair

• Outer Diameter: 3/16″ (4.76 mm);
• Inner Diameter: 3/32″ (2.36 mm);
• Length: 2.4 mm.

Controller wiper button, 1 pc.

Wiper button for all Koford controllers

Replacement brass wiper arm for all Economy/Sebring/Turbo Controllers

JK Wiper arm with wiper button

Old catalog #JK80814

Replacement pair of Bushing Oilites for Turbo Controller Trigger (Requires one pair). Also for adding 1/8" diameter axle to slot car chassis with 1/4" hole.

KOFORD Axle ballbearing 3/32" (2.36 mm), narrow width, open, ultralight, pair

Standard steel axle is a replacement for Womps and Flexi Cars. Can be used for most slot cars that require an 1/8" axle that is 2.625" (2-5/8") wide.

1/8" (3.15 MM) AXLE, (length 69,5 mm) - #HR303

KOFORD Axle ballbearing 3/32" x 3/16" (2.36 mm x 4.76 mm), shielded, pair - #M633

Premium, high-precision ball bearings engineered for professional slot car racing.

KOFORD Ø1/8" (3.15 mm) drill blank axle, length 2.677" (68 mm)  - #M418

1/8 axles with the famous Koford precision fit. The same straightness and size control which racers have long enjoyed with 3/32 axles now comes to 1/8 axles

BSR Crown gear 72 pitch 30 teeth, 2 mm axle, Ø13.05 mm, w/Ti hub, weight 0,95 g.

DRAGSTER LEAD WIRE WITH CLIPS - 3 meters long with nickel plated guide clips

KOFORD Axle ballbearing 3/32" (2.36 mm), ultra premium, shielded, pair - #M217

Ultra Premium shielded rear axle ball bearings, ribbon retainer and ultra precise internal geometry for smooth rotation and the lowest drag. Highest quality steel and ribbon retainer for long life. Made in Switzerland.

ZHB LANE STICKERS, 100 sheets

Lane stickers for model, from 1 to 8 lane

This is a kit of production model 1/32 in the maximum configuration: a three-piece JK chassis, 72 pitch, motor: setup with matched magnets + S16C armature + ballbearings + multi-coil springs + washers, tubes instead of clips, lexan body.

B52 C-Can magnets, type 3, pair

NeAn Clear body Eurosport 1/24U Audi R8

This body is made according to ES-24 rules for chassis Production 1/24

• Made from: Polycarbonate (Lexan)
• For: Eurosport 1/24
• Thickness: .007" (0.175 mm)
• Clear body

NeAn Clear body Eurosport 1/24U Audi R8

This body is made according to ES-24 rules for chassis Production 1/24

• Made from: Polyvinyl chloride (PVC)
• For: Eurosport 1/24
• Thickness: .008" (0.2 mm)
• Clear body

Clear body Eurosport 1/32 Porsche 917

• Made from: Polycarbonate (Lexan)
• For: Eurosport 1/32
• Thickness: .007" (0.175 mm)
• Clear body

Clear body Eurosport 1/24 Cadillac Northstar LMP Race Car

• Made from: Polycarbonate (Lexan)
• For: Eurosport 1/24
• Thickness: .005" (0.125 mm)
• Clear body

Clear body ES G12-32 Mercedes CLK LM

• Made from: Polycarbonate (Lexan)
• For: ES G12-32
• Thickness: .005" (0.125 mm)
• Clear body