JK 3/32" (2.36 mm) .022" (0.55 mm) thick steel axle spacer, 12 psc.

Old catalog #JK178

JK Motor Bracket for Production 1/24 JK 4" "Cheetah X25" - #C40B

Old catalog #JK250115

1/8" X 3/16" (3.15 X 4.76 MM) BUSHINGS IN PRODUCTION CHASSIS, pair

Use for adding 1/8" diameter axle to slot car chassis with 1/4" hole. Raised Speed Ring reduces friction for increase in speed. (Requires one pair per axle.)

REDUCER BUSHING MOUNTS 3/32 BEARINGS ON 1/8

MOSETTI Patriot "Spec" chassis 1/24 Penn/Jersey-ECFS - #MR1234

This is a spec chassis created for the ECFS Production and Penn Jersey Xfinity series. It is the MR1112 Striker Center and the MR3122 Pans

JKPHC1132 - 1/32 Cheetah 11 / 3 piece chassis design for Production 1/32. Sheet of lead in a gift! - #C1

Old catalog #HC1132

Special order!

JKPX321 - 1/32 CHEETAH 11 CHASSIS WITH 1 PAN, 2 piece chassis, for Production 1/32 - #C5

Old catalog #JKX321

JK 1/32 Cheetah 11 JK#C1 & JK#C5 Chassis Center Section - #C1C 

1/32 Center Section replacement for X32 Chassis JKP 1/32 CHEETAH 11 CHASSIS for PRODUCTION 1/32 - #JKPHC1132 & JKP 1/32 CHEETAH.11 CHASSSIS KIT W/1PAN for PRODUCTION 1/32- #JKPX32

Old catalog #JKX32C

JK 1/32 Cheetah 11 JK#C1 & JK#C5 2-piece pans - #C1P

Old catalog #HC1132P

My assembly. Models in the assembly will cost from $300 to $500 and more.... Depending on the configuration. Those. It can be chassis DUBICK, HORKY or CASTRICONE, And motors: setups: ZHB, VALIKO, VOKI, CAHOZA, HORKY or Machkoza, with different armatures.

Delivery of any configurations is possible !!! The average price of the model is indicated.

HD30 Upgrade PCB: Convert your 10 or 15 band Pro Plus or Fanatic controller to our new 30 band high definition design. You get the HD30 circuit board with a standard 148 ohm network board installed. Simply unsolder a few wires and remove the old PCB. Transfer the original brake and sensitivity rheostats over to the new HD30 board. Now bolt the PCB to the frame and solder a few wires to their correct positions. Simple instructions included.

40 amp (70 amp surge) high power relay installs easily on main wires. Includes instructions for all controllers as well as special parts and instructions for Difalco Design "E"Motion electronic controllers and modules. Text plus drawings make our kit easier to install than other brands! 

ZHB Brake rheostat 4.7 Ohms

Wound with flat nichrome wire. Primarily used in controllers manufactured by Nesterenko A.I., but is suitable for any electronic controller.

DIFALCO Brake rheostat for 1/32 - #DD336

Replacement 25 ohm brake rheostat used on all 1/32 controllers.

Brake Rheostat, pro, with knob, variable with off position, reducing washers. 

Same as the 806 but with no knob

Power Transistor, large silver transistor used on all "E"Motion electronic controllers and modules

Sensitivity rheostat replacement for all Difalco controllers

DIFALCO Sensitivity/Traction rheostat 1/8 shaft 50ohm - #DD843

"Banana" connector for controller, 1 pc.

KOFORD Alligator clips, 1 set - #M176

Solid copper alligator clips 

KOFORD Controller boots, 1 set - #M748

Red, White and Black allligator boots

PARMA Turbo Controller - 4 OHM - #264

PARMA Controllers have been the standard in performance since 1968. Their simplicity and durability means many years of dependable service. Resistors can be swapped easily to tailor your handling for different tracks and cars. Use for all 16D, Group 7, Group 12, Group 27 class racing. Turbo - Our most popular performance controller. Features an anodized Turbo Frame, double barrel resistor and 2 additional contact pads to ensure full brake and full power. Features clear handle, nylon trigger with oilites and 14 gauge wire, includes boots/clips.