ZHB

Under the designation ZHB are hidden motors or models, assembly by Andrei Zhbanov

Also these are the products of various manufacturers, the profile of which is not related to slotraising, but we use their products.

• ZHB ES32 18М MOTOR

  Magnet height 11,43 mm (.450"), length 7,62 mm (.300"), outside diameter of magnets 14,65 mm (.577"), armature Koford (or VALIKO ceramic, blue) 25/25-, Ø.485" 25°, rebalanced, shaft 1.5 mm, GRW ballbearings, brush Big Foot for "+", brush Proslot for "-", Cahoza 3 coil springs, TQ silver shunt wire, Alpha teflon spring insulation, Koford spacers.

  Any order of motors discusses individual. Possibility to build motors of individual configurations under order (wire, number of turns, advance angle)

  222.83 $

• ZHB VOKI Mini ES32 Setup Cahoza can 18M MOTOR

  Magnet height 11,43 mm (.450"), length 7,62 mm (.300"), outside diameter of magnets 14,65 mm (.577"), armature Koford (or VALIKO ceramic, blue) 25/25-, Ø.485" 25°, rebalanced, shaft 1.5 mm, GRW ballbearings, brush Big Foot for "+", brush Proslot for "-", Cahoza 3 coil springs, TQ silver shunt wire, Alpha teflon spring insulation, Koford spacers.

  Any order of motors discusses individual. Possibility to build motors of individual configurations under order (wire, number of turns, advance angle)

  260.87 $

• 

  S&K Gear 72 pitch 42 teeth, 0° angle, 3/32" axle, Ø15.46 mm glyed on Proslor axle - #225

  The hub is not cut width, but machined to a diameter 3 mm.

  This gear for ES32 if you use offset rims in gears side or for ES24.

  You can order gluing any gear on any axle. Price for gluing & machining - $5 (ZHB#109)

  12.00 $

• S&K 80 PITCH 43T, 0° angle, 3/32" axle, Ø14.3 mm glued on 3/32" axle ProSlot - ZHB#210

  The hub is cut to a width 3.5 mm & machined to a diameter 3 mm 

  This one intended for Eurosport 1/32

  You can order gluing any gear on any axle. Price for gluing & machining - $5 (ZHB#109

  12.00 $

• VITULA 80 PITCH 43T, 0° angle, 3/32" axle, Ø14.45 mm glued on 3/32" axle ProSlot - ZHB#211

  The hub is cut to a width 3.5 mm & machined to a diameter 3 mm 

  This one intended for Eurosport 1/32

  You can order gluing any gear on any axle. Price for gluing & machining - $5 (ZHB#109

  12.00 $

• VITULA 80 PITCH 43T, 0° angle, 3/32" axle, Ø14.45 mm glued on 3/32" axle ProSlot - ZHB_#211

  The hub is cut to a width 3.5 mm & machined to a diameter 3 mm 

  This one intended for Eurosport 1/32

  You can order gluing any gear on any axle. Price for gluing & machining - $5 (ZHB#109

  12.00 $

• JK 80 PITCH 43T, 0° angle, 3/32" axle, Ø14.28 mm glued on 3/32" axle ProSlot - ZHB#212

  The hub is cut to a width 3.5 mm & machined to a diameter 3 mm 

  This one intended for Eurosport 1/32

  You can order gluing any gear on any axle. Price for gluing & machining - $5 (ZHB#109

  12.00 $

• 

  HORKY BIG HUB 80 PITCH 43T, 0° angle, 3/32" axle, Ø14.35 mm glued on 3/32" axle ProSlot - ZHB#213

  The hub is cut to a width 3.5 mm & machined to a diameter 3 mm 

  This one intended for Eurosport 1/32

  You can order gluing any gear on any axle. Price for gluing & machining - $5 (ZHB#109)

  12.00 $

• 

  ZHB LANE STICKERS, 10 sheets

  ZHB LANE STICKERS, 10 sheets

  Lane stickers for model, from 1 to 8 lane

  1.18 $

• 

  ZHB LANE STICKERS, 100 sheets

  ZHB LANE STICKERS, 100 sheets

  Lane stickers for model, from 1 to 8 lane

  10.48 $

• ZHB PRODUCTION 1/32 MODEL KIT IN THE MINIMUM CONFIGURATION

  This is a kit of production model 1/32 in the simplest configuration: chassis bronze, 64 pitch, engine without modifications, clips instead of tubes, lexan body.

  59.00 $

• ZHB PRODUCTION 1/32 MODEL KIT IN THE MAXIMUM CONFIGURATION

  This is a kit of production model 1/32 in the maximum configuration: a three-piece JK chassis, 72 pitch, motor: setup with matched magnets + S16C armature + ballbearings + multi-coil springs + washers, tubes instead of clips, lexan body.

  118.00 $

• ZHB LAPPING ARMATURE SHAFT TO DIA. 1,5 mm - #104

  ZHB LAPPING ARMATURE SHAFT TO DIA. 1,5 mm - #104

  4.00 $

• 

  ZHB COMMUTATOR GROOVING ON HIGH-PRECISION LATHE "HUDY" - #105

  ZHB COMMUTATOR GROOVING ON HIGH-PRECISION LATHE "HUDY" - #105

  1.31 $

• 

  ZHB Ballbearing 3 х 7 х 3 mm, flanged shielded, 7 balls - 1 Pc. - #3х7х3F

  Ballbearing 3 х 7 х 3 mm,  flanged shielded, 7 balls - 1 Pc. - #3х7х3F

  4.00 $

• 

  S&K 80 PITCH 45T, 0° angle, 2 mm axle, Ø14.9 mm glued on 2 mm axle KOFORD - ZHB#208

  The hub is cut to a width 3.5 mm & machined to a diameter 3 mm 

  This one intended for Eurosport 1/32

  You can order gluing any gear on any axle. Price for gluing & machining - $5 (ZHB#109)

  12.00 $

• S&K 80 PITCH 44T, 0° angle, 3/32" axle, Ø14.6 mm glued on 3/32" axle ProSlot - ZHB#214

  The hub is cut to a width 3.5 mm & machined to a diameter 3 mm 

  This one intended for Eurosport 1/32

  You can order gluing any gear on any axle. Price for gluing & machining - $5 (ZHB#109)

  12.00 $

• 

  ZHB REINFORCED TAPE (w/linear reinforcement), 12 mm x 50 m - #922

  A great option for the beginning racers! 

  2.79 $

• 

  ZHB SET OF STAND FOR SOLDERING IRON WITH VISCOSE SPONGE

  SET OF STAND FOR SOLDERING IRON WITH VISCOSE SPONGE. 

  Very need thing to soldering iron, preventing burning out by them surrounding objects. Also viscose spoge could clean soldering iron tip from all debris

  4.59 $

• 

  ZHB Axle ballbearing 3 х 7 х 3 mm, shielded, 7 balls - 1 Pc. - #3x7x3

  Axle ballbearing 3 х 7 х 3 mm,  shielded, 7 balls - 1 Pc. - #3x7x3

  2.00 $

• 

  ZHB PREPARING WHEELS SET (GLUING & MACHINING) - #106

  ZHB PREPARING WHEELS SET (GLUING & MACHINING) - #106

  3.00 $

• 

  ZHB PAINTING BODY BY AIRBRUSH - #107

  Painting bodies by water-based paints PARMA, under special order.

  3.01 $

• ZHB PREPARING BODY TO RACE (CUTTING, STRENGTHENING & INSTALLATION ON THE MODEL) - # 108

  ZHB PREPARING BODY TO RACE (CUTTING, STRENGTHENING & INSTALLATION ON THE MODEL) - # 108

  5.00 $

• 

  ZHB STAND SLOTLAB #TCS_Alpaha FOR STORAGE WHEELS BOTTLES Ø23.5 mm (JK, Alpha), W/12 BOTTLES, 88 х 117 mm, acrylic

  STAND SLOTLAB #TCS_Alpaha FOR STORAGE WHEELS BOTTLES Ø23.5 mm (JK, Alpha), W/12 BOTTLES, 88 х 117 mm, acrylic

  PARAMETERS

  • Dia. of wheels bottles, mm: 23,5 (JK, Alpha)
  • Quantity of holes for bottles, pcs: 12
  • Quantity of bottles, pcs: 12
  • Size, mm: 88x17
  • Material: acrylic

  
  

  16.00 $