ZHB

Under the designation ZHB are hidden motors or models, assembly by Andrei Zhbanov

Also these are the products of various manufacturers, the profile of which is not related to slotraising, but we use their products.

• 

  HORKY BIG HUB 80 PITCH 44T, 0° angle, 2 mm axle, Ø14.5 mm glued on 2 mm axle KOFORD - ZHB#206

  The hub is cut to a width 3.5 mm & machined to a diameter 3 mm 

  This one intended for Eurosport 1/32

  You can order gluing any gear on any axle. Price for gluing & machining - $5 (ZHB#109)

  12.00 $

• 

  ZHB Axle ballbearing 3 х 7 х 3 mm, shielded, 7 balls - 1 Pc. - #3x7x3

  Axle ballbearing 3 х 7 х 3 mm,  shielded, 7 balls - 1 Pc. - #3x7x3

  2.00 $

• 

  ZHB AXLE Ballbearing 3 х 9 х 3 mm, flanged shielded, 7 balls, pair - #3x9x3F

  AXLE Ballbearing 3 х 9 х 3 mm, flanged shielded, 7 balls, pair - #3x9x3F

  1.42 $

• 

  ZHB Ballbearing 3 х 7 х 3 mm, flanged shielded, 7 balls - 1 Pc. - #3х7х3F

  Ballbearing 3 х 7 х 3 mm,  flanged shielded, 7 balls - 1 Pc. - #3х7х3F

  4.00 $

• 

  ZHB F1 10M SETUP, .256 long - .376 tall - can ID .570

  SPECIAL ORDER!

  F1/32 SETUP 10 MAGNETS

  PARAMETERS

  • Magnets quantity: 10
  • Dia. for gluing magnets: 14.7 mm
  • Outside dia.: .570" 
  • Magnets height: .376" 
  • Magnets length: .256" 
  • For armature: KOFORD ULTRA SHORT (M255EH)
  • Ballbearings: GRW (1,5 mm width)

  This is no actual photo! Actual photos will be added later!

  
  

  201.09 $

• 

  ZHB F1 12M SETUP, .256 long - .376 tall - can ID .570

  SPECIAL ORDER!

  F1/32 SETUP 12 MAGNETS

  PARAMETERS

  • Magnets quantity: 10
  • Dia. for gluing magnets: 14.7 mm
  • Outside dia.: .570" 
  • Magnets height: .376" 
  • Magnets length: .256" 
  • For armature: KOFORD ULTRA SHORT (M255EH)
  • Ballbearings: GRW (1,5 mm width)

  This is no actual photo! Actual photos will be added later!

  
  

  211.96 $

• 

  ZHB F1 TOOL SETUP, .256 long - .376 tall - can ID .570

  F1/32 SETUP TOOL

  PARAMETERS

  • Magnets quantity: 2
  • Dia. for gluing magnets: 14.7 mm
  • Outside dia.: .570" 
  • Magnets height: .376" 
  • Magnets length: .256" 
  • For armature: KOFORD ULTRA SHORT (M255EH)
  • Ballbearings: GRW (1,5 mm width)

  163.04 $

• ZHB PAINT MASK FOR BODY

   ZHB PAINT MASK FOR BODY

  0.13 $

• ZHB VOKI Mini ES32 Setup Cahoza can 10M MOTOR

  Magnet height 11,43 mm (.450"), length 7,62 mm (.300"), outside diameter of magnets 14,65 mm (.577"), armature Koford (or VALIKO ceramic, blue) 25/25-, Ø.485" 25°, rebalanced, shaft 1.5 mm, GRW ballbearings, brush Big Foot for "+", brush Proslot for "-", Cahoza 3 coil springs, TQ silver shunt wire, Alpha teflon spring insulation, Koford spacers.

  Any order of motors discusses individual. Possibility to build motors of individual configurations under order (wire, number of turns, advance angle)

  244.57 $

• 

  BOLID GM FORD AEROMAX BODY, PVC, thickness .015" (0.4 mm), w/interior & w/paint masks

  GM 1/24 FORD AEROMAX Body

  • Made from: Polyvinyl chloride (PVC)
  • For: GM (Truck)
  • Thickness: .015" (0.4 mm)
  • w/interior &
    • w/paint masks

  3.80 $

• 

  CAHOZA 80 PITCH 44T, 0° angle, 2 mm axle, Ø14.5 mm glued on 2 mm axle KOFORD - ZHB#207

  The hub is cut to a width 3.5 mm & machined to a diameter 3 mm 

  This one intended for Eurosport 1/32

  You can order gluing any gear on any axle. Price for gluing & machining - $5 (ZHB#109)

  12.00 $

• 

  CAHOZA 80 PITCH, 45T, 0° angle, 3/32" axle, Ø14.9 mm glued on 3/32" axle CAHOZA - ZHB#227

  The hub is machined to a diameter 3.5 mm

  You can order gluing any gear on any axle. Price for gluing & machining - $5 (ZHB#109)

  
  

  12.00 $

• 

  CAHOZA ES24 glyed gear 72 PITCH 38 teeth (Ø14.52 mm) on 3/32" Proslot axle - ZHB#230

  The hub is not cut width, but machined to a diameter 3 mm.

  This gear for ES32 if you use offset rims in gears side or for ES24.

  You can order gluing any gear on any axle. Price for gluing & machining - $5 (ZHB#109)

  12.00 $

• 

  CAHOZA ES24 glyed gear 72 PITCH 39 teeth (Ø14.52 mm) on 3/32" Proslot axle - ZHB#229

  The hub is not cut width, but machined to a diameter 3 mm.

  This gear for ES32 if you use offset rims in gears side or for ES24.

  You can order gluing any gear on any axle. Price for gluing & machining - $5 (ZHB#109)

  12.00 $

• 

  CAHOZA ES24 glyed gear 72 PITCH 40 teeth (Ø14.85 mm) on 3/32" Proslot axle - ZHB#231

  The hub is not cut width, but machined to a diameter 3 mm.

  This gear for ES32 if you use offset rims in gears side or for ES24.

  You can order gluing any gear on any axle. Price for gluing & machining - $5 (ZHB#109)

  12.00 $

• 

  CAHOZA ES32 glyed gear 72 PITCH 39 teeth (Ø14.52 mm) on 2 mm KOFORD axle - ZHB#226

  The hub is cut to a width 3.5 mm & machined to a diameter 3 mm

  You can order gluing any gear on any axle. Price for gluing & machining - $5 (ZHB#109)

  12.00 $

• 

  CAHOZA ES32 or ES24 glyed gear 72 PITCH 39 teeth (Ø14.52 mm) on 2 mm KOFORD axle - ZHB#228

  The hub is not cut width, but machined to a diameter 3 mm.

  This gear for ES32 if you use offset rims in gears side or for ES24.

  You can order gluing any gear on any axle. Price for gluing & machining - $5 (ZHB#109)

  12.00 $

• 

  CAHOZA GEAR CAHOZA 64 PITCH, 36T, 0° angle, 3/32" axle, Ø15.00 mm glued on 3/32" axle CAHOZA - CAH#6-AG

  The hub is not cut width, but machined to a diameter 3 mm.

  This gear for ES32 if you use offset rims in gears side or for ES24.

  You can order gluing any gear on any axle. Price for gluing & machining - $5 (ZHB#109)

  12.00 $

• 

  CAHOZA GEAR CAHOZA 64 PITCH, 36T, 0° angle, 3/32" axle, Ø15.00 mm glued on 3/32" axle CAHOZA, hub machined to the dia. 3.7 mm - CAH#6-AG

  CAHOZA GEAR CAHOZA 64 PITCH, 36T, 0° angle, 3/32" axle, Ø15.00 mm glued on 3/32" axle CAHOZA, hub machined to the dia. 3.7 mm

  This gear for ES32 if you use offset rims in gears side or for ES24.

  You can order gluing any gear on any axle. Price for gluing & machining - $5 (ZHB#109)

  12.00 $

• 

  CAHOZA glyed 72 PITCH 40T (Ø14.8 mm) gear on 2 mm KOFORD axle - ZHB#221

  The hub is cut to a width 3.5 mm & machined to a diameter 3 mm

  You can order gluing any gear on any axle. Price for gluing & machining - $5 (ZHB#109)

  12.00 $

• 

  HORKY BIG HUB 80 PITCH 43T, 0° angle, 3/32" axle, Ø14.35 mm glued on 3/32" axle ProSlot - ZHB#213

  The hub is cut to a width 3.5 mm & machined to a diameter 3 mm 

  This one intended for Eurosport 1/32

  You can order gluing any gear on any axle. Price for gluing & machining - $5 (ZHB#109)

  12.00 $

• 

  HORKY BIG HUB 80 PITCH, 45T, 0° angle, 3/32" axle, Ø14.9 mm glued on 3/32" axle ProSlot - ZHB#219

  The hub is machined to a diameter 3.5 mm

  You can order gluing any gear on any axle. Price for gluing & machining - $5 (ZHB#109)

  12.00 $

• 

  JK 72 PITCH, 40T, 0° angle, 2 mm axle, Ø14.65 mm, glued on 2 mm axle KOFORD - ZHB#232

  The hub is cut to a width 3.5 mm & machined to a diameter 3 mm

  You can order gluing any gear on any axle. Price for gluing & machining - $5 (ZHB#109)

  12.00 $

• JK 80 PITCH 43T, 0° angle, 3/32" axle, Ø14.28 mm glued on 3/32" axle ProSlot - ZHB#212

  The hub is cut to a width 3.5 mm & machined to a diameter 3 mm 

  This one intended for Eurosport 1/32

  You can order gluing any gear on any axle. Price for gluing & machining - $5 (ZHB#109

  12.00 $