KOFORD
-
KOFORD Flanged bushing 2 x 5 mm for can & endbell, 1 pc. - #M509
KOFORD Flanged bushing 2 x 5 mm for can & endbell, 1 pc. - #M509
5MM flanged bushing for Super Feather can & endbell.
-
KOFORD BRASS RETAINERS FOR .063 TUBING 1 pc. - #M536
Machined brass retainers (eyelets) for .063 tubing
Perfect fit for attaching the front wheels to the formula 1/32! (inner dia. 1.6 mm)
-
KOFORD ARMATURE TUBE, Ø13.5 mm - M602
KOFORD ARMATURE TUBE, Ø13.5 mm - M602
-
KOFORD 3/32" (2.36 mm) .010" (0,254 mm) thick, plastic axle spacer, 1 pc. - #M704
3/32" (2.36 mm) .010" (0,254 mm) thick, plastic axle spacer, 1 pc.
-
KOFORD LEAD WIRE RETAINER, 1 pc. - #M324
Lead wire retainer. Prevents lead wire from dragging on track, solders to middle rail.
-
Koford Yellow spoiler sticker, 1 pc. - #M719
Koford Yellow spoiler sticker, 1 pc. - #M719
Decorate your body with branded stickers :)
-
KOFORD 3/32" (2.36 MM), .175" (4.45 MM) LONG, PLASTIC AXLE SPACER, 1 pc. - #M449
Plastic axle spacer for narrow motor box cars with 3/32 axles. A snug fit on the axle so that it doesn't fall off
-
KOFORD CONTROLLER SPRINGS - #M371
Controller springs for all Koford controllers
-
KOFORD Teflon® spring insulation, 30 cm - #M267
KOFORD Teflon® spring insulation, 30 cm - #M267
Teflon® spring insulation, perfect fit on springs
-
KOFORD RECTANGULAR MOTOR BOX WITH FOAM, plastic, 1 pc. - #603
Motor Boxes with 2 piece yellow foam
-
KOFORD Flux brush - #M424
At last a flux brush which is the correct size for slot car racing and will hold up to the attack of acid flux.
-
KOFORD 408 BRAID, pair-#M661
The best choise for class Formula 1/32
-
KOFORD BRASS GUIDE NUT 9.5 MM SOCKET - #M615
Brass guide nut. Adds one gram nose weight
-
KOFORD AXLE BEARING INSTALATION SPRING - M634
Coil spring for aligning axle bearings - Perfect rear axle bearing alignment - Slide over axle and slide through axle holes in chassis. Slide on bearings in place and square. Solder bearings from the inside of pillow blocks.
-
KOFORD Controller wiper button, 1 pc. - #M738
Controller wiper button, 1 pc.
Wiper button for all Koford controllers
-
KOFORD STEEL PIN TUBING, lenght 80 mm, 1 pc. - #M259
Precut spring temper stainless steel pin tubing, fits full width of car.
-
KOFORD SELF TAP MOTOR SCREWS, 4 pcs. - #M466-4
Self tapping Box Stock can & endbell screws. 1/8" long for minimum weight and to provide can screw clearance on Feather set ups. Tighten with standard wheel wrench.
Suitable for everyone plastic endbells, besides endbells CAHOZA
-
KOFORD ALUMINUM SPRING CUPS (for 3 coils spring) ON ENDBELLS FOR EUROSPORT MOTORS, pair - #281
Self centering ultra light aluminum alloy spring cups for Koford set ups
-
KOFORD CUT BRASS PIN TUBE, lenght 12.8 mm, 4 psc. - #M453
Precut brass pin tubes. Use for solid mount EDM chassis for the front mount or use in all chassis for pin tubes.
-
KOFORD Ultralight qualifying wire, 1 pc. - #M383
KOFORD Ultralight qualifying wire, 1 pc. - #M383
The Nat’s TQ ultralight qualifying lead wire made from ML magnet wire. Enough for several cars.
-
KOFORD Ø1/8" (3.15 mm) drill blank axle - #M418
KOFORD Ø1/8" (3.15 mm) drill blank axle - #M418
1/8 axles with the famous Koford precision fit. The same straightness and size control which racers have long enjoyed with 3/32 axles now comes to 1/8 axles
-
KOFORD DRILLED ALUM ANODIZED GUIDE NUT, 9,5 MM SOCKET - #M302
Lightweight drilled, anodized aluminum guide nut.
-
KOFORD Lead wire 18Ga (0,82 mm²), super ultra flex silcone, w/clips, 1 pr. - #M430
KOFORD Lead wire 18Ga (0,82 mm²), super ultra flex silcone, w/clips, 1 pr. - #M430
Lightweight ultraflex 413 strand 18 guage lead wire with superthin wall insulation. Reduced insulation wall thickness results a 14% weight savings over competitors lead wire. Worlds and Nat's winner. With clips
-
KOFORD .010" (0.254 MM) PHOS BRONZE GUIDE WASHER, 6 pcs. - #M321
.010 thick Phosphorous Bronze guide washer. Use to adjust guide height Will not deflect like stacked Teflon® washers. Packaged 6 per bag.