KOFORD
-
KOFORD T-SHIRT, SIZE- XL - #240XL
KOFORD T-SHIRT, SIZE- XL
A fine T-shirt made from cotton! It does not stretch, even after a lot of washing.
-
KOFORD T-SHIRT, SIZE- M - #240M
KOFORD T-SHIRT, SIZE- M
A fine T-shirt made from cotton! It does not stretch, even after a lot of washing.
-
KOFORD Axle ballbearing 3/32" (2.36 mm), narrow width, open, ultralight, pair - #M235
KOFORD Axle ballbearing 3/32" (2.36 mm), narrow width, open, ultralight, pair
-
KOFORD Ultra precision axle Ø3/32" (2.36 mm), length 53 mm, 1 cd. (6 pcs.) - #M623R
KOFORD Ultra precision axle Ø3/32" (2.36 mm), length 53 mm, 1 cd. (6 pcs.) - #M623R
Unplated 3/32 axles for those who wish to flat their own. Superior rust resistance to other unplated axles. These axles have a super hard low friction coating which will not rust.
-
KOFORD S.B.F. II premium horizontal brushes, 1 cd. ( 6 pr.) - #M485
KOFORD S.B.F. II premium horizontal brushes, 1 cd. ( 6 pr.) - #M485
S.B.F. II Horizontal brushes for 16D, Super 16D, Competitor, etc. The Worlds best motor brush, winner of countless World and National championships. These are the brushes which our M476 and M244 brushes are machined from.
-
KOFORD T-SHIRT, SIZE- XXL - #M204-XXL
KOFORD T-SHIRT, SIZE- XXL
A fine T-shirt made from cotton! It does not stretch, even after a lot of washing.
-
KOFORD Premium horizontal SBF II brushes (for C12, G27) w/precision ground shunt slot, 1 cd. (6 pr.) - #M476
KOFORD Premium horizontal SBF II brushes (for C12, G27) w/precision ground shunt slot, 1 cd. (6 pr.) - #M476
Now shortened and ready to use. Use with M313 light tension or M276 heavy tension springs and M329 or M295 heat transfer compound.
-
KOFORD HARD PREMIUM BRUSHES BIGFOOT, VERTICAL, 6 pairs - #M244A
Hard premium brushes for vertical brush hoods, open and group classes
6 pairs prepared for installation in vertical brush hoods brushes packed in easy opened box.
-
KOFORD ENBELL FOR SETUP KOFORD M652 UNDER ARMATURE W/RING - #M287L
ENBELL FOR SETUP KOFORD #M652 UNDER ARMATURE W/RING - #M287L
-
KOFORD EDM drilled/wire cut .060" hollow 3/32" rear axle - #M697F
KOFORD EDM drilled/wire cut .060" hollow 3/32" rear axle - #M697F
EDM drilled and wire cut flatted .060 hollow race axle. Lighter and 50% stronger the M445F
-
KOFORD T-SHIRT, SIZE- XXXL - #M204-XXXL
KOFORD T-SHIRT, SIZE- XXXL
A fine T-shirt made from cotton! It does not stretch, even after a lot of washing.
-
KOFORD EDM drilled/wire cut .060" hollow 3/32" rear axle (length 55 mm) - #M754
KOFORD EDM drilled/wire cut .060" hollow 3/32" rear axle (length 55 mm) - #M754
E24 2.165" (55mm) long EDM drilled and wire cut .060 hole hollow axle with no flats. Light and strong.
-
KOFORD Ultrastrong radial C-Can drag magnets- #M592
KOFORD Ultrastrong radial C-Can drag magnets
Ultrastrong radial drag magnets, when used with M593 treated can produces 4% more flux then competitors wide can and .170 thick quad magnets without the problems of nonstandard size cans. .165 thick x .520 long
-
KOFORD Lead wire 18Ga (0,82 mm²), super ultra flex silcone, 9 m. (30 ft.) - #М667
KOFORD Lead wire 18Ga (0,82 mm²), super ultra flex silcone, 9 m. (30 ft.) - #М667
Lightweight ultraflex 413 strand 18 guage lead wire with superthin wall insulation. Reduced insulation wall thickness results a 14% weight savings over competitors lead wire. Worlds and Nat's winner.
-
KOFORD Axle ballbearing 3/32" (2.36 mm), ultra premium, shielded, pair - #M217
KOFORD Axle ballbearing 3/32" (2.36 mm), ultra premium, shielded, pair - #M217
Ultra Premium shielded rear axle ball bearings, ribbon retainer and ultra precise internal geometry for smooth rotation and the lowest drag. Highest quality steel and ribbon retainer for long life. Made in Switzerland.
-
KOFORD SETUP FOR EUROSPORT MOTORS, EXTERNAL DIA. .620" (15.75 MM), HEIGHT .430" (10.9 MM), NICKEL-PLATED -#M652
SETUP FOR ASSEMBLY EUROSPORT MOTORS, NICKEL-PLATED
PARAMETERS:
- EXTERNAL DIA. .620" (15.75 MM)
- HEIGHT .430" (10.9 MM)
-
KOFORD REPLACEMENT ARMATURE FOR JK HAWK - #M644
Koford replacement arm for JK Hawk. Plated better then drill blank shaft, 800° epoxy. Requires JK replacement endbell for Koford arms.
-
KOFORD 760" LONG, C12 ARMATURE (for set in Eurosport motors) - #М467-12C
race arm, 32° .490 C12 arm .760 long, 2006 Nat’s winner Pro
Alternative to expensive Eurosport class armatures. Suitable for all setups, except the latest micro-motors for F 1/32.
-
KOFORD Crown gear 48 pitch 27 teeth, 3/32" axle, narrowed & lightened, 1 cd. (6 pcs.) - #M671-27
KOFORD Crown gear 48 pitch 27 teeth, 3/32" axle, narrowed & lightened, 1 cd. (6 pcs.) - #M671-27
-
KOFORD Crown gear 48 pitch 28 teeth, 3/32" axle, narrowed & lightened, 1 cd. (6 pcs.) - #M671-28
KOFORD Crown gear 48 pitch 28 teeth, 3/32" axle, narrowed & lightened, 1 cd. (6 pcs.) - #M671-28
Narrowed and lightened precision low wobble 28 tooth x 3/32 crown gears. Precision bored axles hole and lightweight magnesium hub
-
KOFORD DIAMOND WHEEL FOR MAGNETS .538"
ZHB DIAMOND WHEEL FOR MAGNETS Ø13.70 mm
Special order
-
KOFORD DIAMOND WHEEL FOR MAGNETS .500"
ZHB DIAMOND WHEEL FOR MAGNETS Ø13.70 mm
Special order
-
KOFORD Neo top gun C-Can drag magnets - #M596
KOFORD Neo top gun C-Can drag magnets - #M596
-
KOFORD G12 Armature for Hawk6 Neo Magnet Setup Only 40 Degrees - #M645-12-40
G12 arm to fit JK Hawk 6 bonded neo magnet set up. Better then drill blank shaft, 800° epoxy. 40° timing. recommended for neo magnet set ups only.