KOFORD Ø.536" (13.61 mm) BEARING ASSEMBLY TOOL (for motor)- KOF188-536

SPECIAL ORDER!

KV TIRE TRUER
3/32" and 2 mm axles included. 1/8” axle available separate. Plastic box for storage included!! (NeAn #170)
Black anodozed. Construction with two types of sandpaper and two belts. Adjustable needle for removing the external diameter of the donut before accurate grind. Also, this needle can be used to cut the width of the donuts using the holes in the base (16 mm and 20 mm)

KV TIRE TRUER with
DUBICK Engineering diamond files for rough 60 grit (grain diametr 0,250 mm) & finish 120 grit (grain diametr 0,125 mm) machining. Plastic box for storage included!! (NeAn #170)
3/32" and 2 mm axles included black anodozed. Construction with two types of diamond files and two belts. Adjustable needle for removing the external diameter of the donut before accurate grind. Also, this needle can be used to cut the width of the donuts using the holes in the base (16 mm and 20 mm).

PARMA Phenolic heat resistant tech block recessed for guide & tires - #MID414

CAHOZA Phenolic insulators, ID 1,5 mm x OD 3 mm x thick. 0,5 mm, 24 pcs. - #158

phenolic insulators, use on all aluminium endbells, suitable for anodised spring posts #154, #157, inside diameter 1,5mm, outside diameter 3mm, thickness 0,5mm, packed by 24pcs

Koford Engineering apron with 3 sections

TAMIYA Masking tape for curves, width 5 mm

Length of roll: 20m
A soft resin material is used, allowing the tape to adhere in a curved line while preventing paint from seeping into masked off areas.
Use of narrower tape is recommended for sharper curves.

TAMIYA Masking tape, width 6 mm

• It even adheres well to uneven surfaces, but is easy to remove.
• Has enough elasticity to work well on curves and small edges.
• Paint does not bleed though the tape.

Comes in its own dispenser with cutter to avoid rough edges.

TQ Lead wire 20Ga (section 0,52 mm²), black 1 m (3 ft) - #TQ2031

266 strand bare copper conductor with thin silicone insulation. 1.75mm OD available in Black only. Not the lightest leadwire available but has approx. 75% more copper in the conductor to deliver more current and less loss

DUBICK TECH BLOCK WITH MAGNETS - #205

Textolite tech block for models with fixed samarium-cobalt magnets. It is made with a cut zone of guide and rear wheels. Has an even working plane.

RALPH THORNE Flux Brush, 1 pc.

1 disposable flux brush with adjustable length handles.

CAHOZA Low profile long cut down nylon elastic guide, blue, w/out thread - #335

long cut down guide for integral guide tongue chassis, lenght 26.8 mm, special shape of keel (see picture), content: blue nylon, glass fibre, these guides have minimum content of glass fibre for higher elasticity, very precise, high quality material used

BPA Clear Body Eurosport 1/24 BMW LMR

• Made from: Polycarbonate (Lexan)
• For: Eurosport 1/24
• Thickness: .007" (0.175 mm)
• Clear body

BPA Clear Body Eurosport 1/24 BMW LM

• Made from: Polycarbonate (Lexan)
• For: Eurosport 1/24
• Thickness: .005" (0.125 mm)
• Clear body

JK Replacement tire & gear wrench tip .050", straight, dia. 3 mm - #L11

Old catalog #JK80421

10 feets of 20 gauge Black wire

MID AMERICA Mockingbird motor

CAHOZA EDM pinion 64 pitch, 7T, 0° angle, 2 mm bore, special black cover - #12

EDM pinions 64 pitch 7T - 2mm hole, plated with special black cover especially developed for Cahoza, this cover enhances lubricity 8 times and repels solder so teeth cannot be soldered through, after application the pinion hole is firmly cut to exact size and solder then sticks perfectly in, made from stainless steel 45 HRc, suitable for all types of gears, ideal for Cahoza 64 pitch gears

DUBICK Holder for the armatures & armatures in the tubes

GOLDEN SILICON WIRE 35 cm

MID AMERICA Guide nut - aluminum pin drive, turquoise, 1 cd. (6 pcs.) - #MID138T

Fits with #MID138 

DUBICK set of contacts for the controller. Made from brass and GOLD PLATED.

Fit for Parma, Jk and RedFox controller triggers. Full analog Parma #355D TURBO CONTACTS & TERMINALS and fit for Parma turbo controller frame.

Diamond Head C can set up Kit w/ Bushings C Can Set Up Very High Quality Set up kit with Magnets and brush springs

Deluxe Axle and pinion gear checker. Checks to make sure they are straight.