KOFORD
-
KOFORD HEAT TRANSFER COMPOUND - M295
Heat transfer compound.
Apply between brush and hood on motors to reduce comm temperatures and increase reliability, also especially effective for removable soldering iron tips.
-
KOFORD LOW TEMP SOLDER W/FLUX CORE - #M444
Like 60/40 but with higher strength. Use for installing motor to chassis (not lead wires), and for assembling all joints on aluminum chassis except for rear motor braces and pillow blocks
-
KOFORD Pinion 64 pitch, 8T, 0° angle, 2 mm bore, Black Diamond coated - #M542
KOFORD Pinion 64 pitch, 8T, 0° angle, 2 mm bore, Black Diamond coated - #M542
8 T Black Diamond coated pinion with boss for greater solder surface area for use with G7. Coating reduces friction and prevents solder from flowing into teeth. Use against plastic spurs only
-
KOFORD STANDART PROFILE GRAPHITE GUIDE, THREADED - #M273
Precision threaded graphite guide with lead wire slots.
On each one guide there is an inscription «STARBURST»
-
-
KOFORD Crown gear 48 pitch 28 teeth, 3/32" axle, narrowed & lightened - #M671-28
KOFORD Crown gear 48 pitch 28 teeth, 3/32" axle, narrowed & lightened - #M671-28
Narrowed and lightened precision low wobble 28 tooth x 3/32 crown gears. Precision bored axles hole and lightweight magnesium hub
-
KOFORD Crown gear 48 pitch 28 teeth, 3/32" axle, narrowed & lightened, 1 cd. (6 pcs.) - #M671-28
KOFORD Crown gear 48 pitch 28 teeth, 3/32" axle, narrowed & lightened, 1 cd. (6 pcs.) - #M671-28
Narrowed and lightened precision low wobble 28 tooth x 3/32 crown gears. Precision bored axles hole and lightweight magnesium hub
-
KOFORD CUT BRASS PIN TUBE, lenght 12.8 mm, 24 psc. in box - #M453
Precut brass pin tubes. Use for solid mount EDM chassis for the front mount or use in all chassis for pin tubes.
-
KOFORD STEEL PIN TUBING, lenght 80 mm, 1 pc. - #M259
Precut spring temper stainless steel pin tubing, fits full width of car.
-
KOFORD ARMATURE ULTRASHORT FOR F1/32, WINDINGS 45/29, DIA. 0.465", STACK 0.235", ADVANCE ANGLE 18º, BALANCED, shaft lapping to 1.5 mm - M255EH (CUSTOM)
ARMATURE ULTRASHORT FOR F1/32, 45/29, BALANCED, H blank ultrashort custom Euro arm with angled comm tabs for F1
PARAMETERS:
- Wingings: 45/29
- Dia.: 0.465"
- Stack: 0.235"
- Long (by ballbearings): 0.664"
- Advance angle: 18
-
KOFORD ARMATURE ULTRASHORT FOR F1/32, WINDINGS 49/28, DIA. 0.465", STACK 0.235", ADVANCE ANGLE 20º, BALANCED, shaft lapping to 1.5 mm - M255EH (CUSTOM)
ARMATURE ULTRASHORT FOR F1/32, 49/28, BALANCED, H blank ultrashort custom Euro arm with angled comm tabs for F1
PARAMETERS:
- Wingings: 49/28
- Dia.: 0.465"
- Stack: 0.235"
- Long (by ballbearings): 0.664"
- Advance angle: 20
-
KOFORD ARMATURE ULTRASHORT FOR F1/32, WINDINGS 49/30, DIA. 0.465", STACK 0.235", ADVANCE ANGLE 28º, BALANCED, shaft lapping to 1.5 mm - M255EH (CUSTOM)
ARMATURE ULTRASHORT FOR F1/32, 49/30, BALANCED, H blank ultrashort custom Euro arm with angled comm tabs for F1
PARAMETERS:
- Wingings: 49/30
- Dia.: 0.465"
- Stack: 0.235"
- Long (by ballbearings): 0.664"
- Advance angle: 28
-
KOFORD 760" LONG, C12 ARMATURE (for set in Eurosport motors) - #М467-12C
race arm, 32° .490 C12 arm .760 long, 2006 Nat’s winner Pro
Alternative to expensive Eurosport class armatures. Suitable for all setups, except the latest micro-motors for F 1/32.
-
-
KOFORD Ø.539" (13.69 mm) bearing assembly tool (for motor) - #M188-539
KOFORD Ø.539" (13.69 mm) bearing assembly tool (for motor) - #M188-539
Prepare your motor fast & precise.
-
-
KOFORD Ø.541" (13.74 mm) bearing assembly tool (for motor) - #M188-541
KOFORD Ø.541" (13.74 mm) bearing assembly tool (for motor) - #M188-541
Prepare your motor fast & precise.
-
KOFORD Ø.542" (13.77 mm) bearing assembly tool (for motor) - #M188-542
KOFORD Ø.542" (13.77 mm) bearing assembly tool (for motor) - #M188-542
Prepare your motor fast & precise.
-
KOFORD Ø.560" (14.22 mm) bearing assembly tool (for motor) - #M188C-560
KOFORD Ø.560" (14.22 mm) bearing assembly tool (for motor) - #M188C-560
Koford Bearing installation tool made out of aluminum. Machined aluminum with 2mm shaft useful in gluing in magnets and installing can end bearings and oilites. Available in many sizes ranging from .468 to .590
Actual photo will be added soon :)
-
KOFORD Ø.569" (14.45 mm) bearing assembly tool (for motor) - #M188-569
KOFORD Ø.569" (14.45 mm) bearing assembly tool (for motor) - #M188-569
Prepare your motor fast & precise.
-
KOFORD Ø.571" (14.50 mm) bearing assembly tool (for motor) - #M188-571
KOFORD Ø.571" (14.50 mm) bearing assembly tool (for motor) - #M188-571
Prepare your motor fast & precise.
-
KOFORD Ø.580" (14.73 mm) bearing assembly tool (for motor) - #M188C-580
KOFORD Ø.580" (14.73 mm) bearing assembly tool (for motor) - #M188C-580
Koford Bearing installation tool made out of aluminum. Machined aluminum with 2mm shaft useful in gluing in magnets and installing can end bearings and oilites. Available in many sizes ranging from .468 to .590
-
KOFORD HIGH TEMP ENDBELL EPOXY, one-component - #M385
High temp. endbell epoxy. Optimized for use in endbells. Oven cure
-
KOFORD Pinion 64 pitch, 8T, 0° angle, 2 mm bore, pinned, Black Diamond coated - #M515
KOFORD Pinion 64 pitch, 8T, 0° angle, 2 mm bore, pinned, Black Diamond coated - #M515
Multiple Nat's winner. Pinned 8T Black Diamond coated pinions for G7 racing. Coating reduces friction and prevents solder from flowing into teeth. Use with M636 pinion wire.