Tools (Misc)
-
ZHB Set of steel files, 3 pcs.
ZHB Set of steel files, 3 pcs.
-
MID AMERICA Dual tip body detailing pen - #MID441
MID AMERICA Dual tip body detailing pen
-
KOFORD AXLE BEARING INSTALATION SPRING - M634
Coil spring for aligning axle bearings - Perfect rear axle bearing alignment - Slide over axle and slide through axle holes in chassis. Slide on bearings in place and square. Solder bearings from the inside of pillow blocks.
-
TAMIYA 30 ADDITIONAL BLADES FOR DESIGN KNIFE #TAM74020 - #TAM74074
Special order!
Additional blades for TAMIYA DESIGN KNIFE - #TAM74020
-
KOFORD .003" (0,07MM) AXLE SPACING TOOL 3/32 - #M572
003 Side play adjusting tool for 3/32 axles. Allows you to quickly get the perfect side play every time
-
KOFORD SIDE PLAY ADJUSTING TOOL (0.13 MM) - #M388
Side play adjusting tool for the rear axle of non ball bearing cars. Allows you to quickly get the perfect side play every time.
-
ZHB Metal drill, dia. 2,1 mm
ZHB Metal drill, dia. 2,1 mm
Made in USSR!
-
JK Phillips Screwdriver for JK#M3 & JK#M6 Motors - #L9
JK Phillips Screwdriver for JK#M3 & JK#M6 Motors - #L9
Old catalog #JK8039
-
KOFORD ALIGNMENT BAR W/HOLES - #M148
Alignment bar with holes, provided with centering holes for both vertical and horizontal style brush hoods. The essential tool for motor assembly, used by motor builders world wide
-
ZHB SET OF BRUSHES WITH THE STEEL, COPPER AND VISCOSE BRISTLE, 3 pcs.
SET OF BRUSHES WITH THE STEEL, COPPER AND VISCOSE BRISTLE, 3 pcs.
Braid/Chassis Brush. Features super strong bristles and rugged handle - makes quick work of serious braid work or the removal of stubborn chassis crud.
Brush made of stainless steel for fluffing brushes in a guide
-
ZHB CONDUCTOR FOR SET THE MOTOR ON F1, motor shaft 1,5 mm, rear axle 2,36 mm - DB#200-st-1.5
CONDUCTOR FOR SET THE MOTOR ON F1, motor shaft 1,5 mm, rear axle 2,36 mm - DB#200-st-1.5
Convenient tool for accurate and fast installation of the motor on F1: fixes the center of the motor shaft and the axis of the rear wheels in the same plane, after which the motor is soldered.
-
ZHB CONDUCTOR FOR SET THE MOTOR ON F1, motor shaft 2 mm, rear axle 3/32" - DB#200-3/32-2
CONDUCTOR FOR SET THE MOTOR ON F1, motor shaft 2 mm, rear axle 2 mm - DB#200-2-2
Convenient tool for accurate and fast installation of the motor on F1: fixes the center of the motor shaft and the axis of the rear wheels in the same plane, after which the motor is soldered.
-
MG ALLEN WRENCH HANDLE W/GUIDE TOOL 9 mm. FOR INSERTS WITH A DIA. 2 mm, green, anodized
For fixing of an insertion the hole, in which the thread 4/40" as in rims and gearwheels is cut, is drilled.
-
TWP Pin body harpoon - #TWP-PIN
TWP Pin body harpoon - #TWP-PIN
Convenient tool for the body preparing!
-
ZHB SCISSORS MEDICAL STRAIGHT
SCISSORS MEDICAL STRAIGHT
Scissors for cutting models body and other things such as adhesive tape, lexan for strengthening, paper or cardboard. The best medical stanles steel!
-
K&S Engineering Hand tap 0-80" - #KS435
K&S Engineering Hand tap 0-80" - #KS435
-
WRIGHTWAY Body pin punch - #WW90
WRIGHTWAY Body pin punch - #WW90
Body Pin Punches are for making pin holes in bodies.
-
WIHA PRECISION TORX SCREWDRIVER T5 x 40mm(for screws in setups VOKI, Proslot X12, e.t.c) - #26705
Precision Torx Screwdriver T5 x 40mm
Rotating cap for precise turning and control with fingertip
Precision handle - high quality plastic, cadmium free
Molded on tapered handle allows rapid rotation
High performance blade - CVM steel, hard chrome finished
Tip - precision ground for exact fit, hard chromed non-slip surface
Blade Length: 40mm (1.6") -
ZHB TAP 0-80 (1,52 mm) FOR CUTTING OF AN INCH THREAD IN ENDBELLS
TAP 0-80 (1,52 mm) FOR CUTTING OF AN INCH THREAD IN ENDBELLS