Tools (Misc)
-
ZHB Set of steel files, 3 pcs.
ZHB Set of steel files, 3 pcs.
-
MID AMERICA Dual tip body detailing pen - #MID441
MID AMERICA Dual tip body detailing pen
-
KOFORD AXLE BEARING INSTALATION SPRING - M634
Coil spring for aligning axle bearings - Perfect rear axle bearing alignment - Slide over axle and slide through axle holes in chassis. Slide on bearings in place and square. Solder bearings from the inside of pillow blocks.
-
TAMIYA 30 ADDITIONAL BLADES FOR DESIGN KNIFE #TAM74020 - #TAM74074
Special order!
Additional blades for TAMIYA DESIGN KNIFE - #TAM74020
-
KOFORD .003" (0,07MM) AXLE SPACING TOOL 3/32 - #M572
003 Side play adjusting tool for 3/32 axles. Allows you to quickly get the perfect side play every time
-
KOFORD SIDE PLAY ADJUSTING TOOL (0.13 MM) - #M388
Side play adjusting tool for the rear axle of non ball bearing cars. Allows you to quickly get the perfect side play every time.
-
ZHB Metal drill, dia. 2,1 mm
ZHB Metal drill, dia. 2,1 mm
Made in USSR!
-
JK Phillips Screwdriver for JK#M3 & JK#M6 Motors - #L9
JK Phillips Screwdriver for JK#M3 & JK#M6 Motors - #L9
Old catalog #JK8039
-
KOFORD ALIGNMENT BAR W/HOLES - #M148
Alignment bar with holes, provided with centering holes for both vertical and horizontal style brush hoods. The essential tool for motor assembly, used by motor builders world wide
-
ZHB SET OF BRUSHES WITH THE STEEL, COPPER AND VISCOSE BRISTLE, 3 pcs.
SET OF BRUSHES WITH THE STEEL, COPPER AND VISCOSE BRISTLE, 3 pcs.
Braid/Chassis Brush. Features super strong bristles and rugged handle - makes quick work of serious braid work or the removal of stubborn chassis crud.
Brush made of stainless steel for fluffing brushes in a guide
-
ZHB CONDUCTOR FOR SET THE MOTOR ON F1, motor shaft 1,5 mm, rear axle 2,36 mm - DB#200-st-1.5
CONDUCTOR FOR SET THE MOTOR ON F1, motor shaft 1,5 mm, rear axle 2,36 mm - DB#200-st-1.5
Convenient tool for accurate and fast installation of the motor on F1: fixes the center of the motor shaft and the axis of the rear wheels in the same plane, after which the motor is soldered.
-
ZHB CONDUCTOR FOR SET THE MOTOR ON F1, motor shaft 2 mm, rear axle 3/32" - DB#200-3/32-2
CONDUCTOR FOR SET THE MOTOR ON F1, motor shaft 2 mm, rear axle 2 mm - DB#200-2-2
Convenient tool for accurate and fast installation of the motor on F1: fixes the center of the motor shaft and the axis of the rear wheels in the same plane, after which the motor is soldered.
-
MG ALLEN WRENCH HANDLE W/GUIDE TOOL 9 mm. FOR INSERTS WITH A DIA. 2 mm, green, anodized
For fixing of an insertion the hole, in which the thread 4/40" as in rims and gearwheels is cut, is drilled.
-
TWP Pin body harpoon - #TWP-PIN
TWP Pin body harpoon - #TWP-PIN
Convenient tool for the body preparing!
-
ZHB SCISSORS MEDICAL STRAIGHT
SCISSORS MEDICAL STRAIGHT
Scissors for cutting models body and other things such as adhesive tape, lexan for strengthening, paper or cardboard. The best medical stanles steel!
-
K&S Engineering Hand tap 0-80" - #KS435
K&S Engineering Hand tap 0-80" - #KS435
-
WRIGHTWAY Body pin punch - #WW90
WRIGHTWAY Body pin punch - #WW90
Body Pin Punches are for making pin holes in bodies.
-
WIHA PRECISION TORX SCREWDRIVER T5 x 40mm(for screws in setups VOKI, Proslot X12, e.t.c) - #26705
Precision Torx Screwdriver T5 x 40mm
Rotating cap for precise turning and control with fingertip
Precision handle - high quality plastic, cadmium free
Molded on tapered handle allows rapid rotation
High performance blade - CVM steel, hard chrome finished
Tip - precision ground for exact fit, hard chromed non-slip surface
Blade Length: 40mm (1.6") -
ZHB TAP 0-80 (1,52 mm) FOR CUTTING OF AN INCH THREAD IN ENDBELLS
TAP 0-80 (1,52 mm) FOR CUTTING OF AN INCH THREAD IN ENDBELLS
-
DUBICK Tweezers stainless steel, non-magnetic - #DB715
DUBICK Tweezers stainless steel, non-magnetic - #DB715
Perfect for work with small parts!
-
MID AMERICA Body harpoon - #MAR104
MID AMERICA Body harpoon
Body Harppon for punching pin holes in lexan bocies
-
TAMIYA DESIGN KNIFE with 30 additional blades- #TAM74020
Special order!
-
JK Pinion gear puller T-Handle - #L17
JK Pinion gear puller T-Handle - #L17
Old catalog #JK8063
-
WRIGHTWAY DIAMOND CUTTING TOOLS, 15 pcs. - #WW26
DIAMOND CUTTING TOOLS, 15 pcs. - #WW26
15 pieces FITS MOST MOTO TOOLS
-
INORS TAP 4/40"
TAP 4/40"
-
S&K F1 motor adjustment tool for offset crowns with 3/32" axle - #0103
CONDUCTOR FOR SET THE MOTOR ON F1, WITH THE CENTER SHIFTED DOWN BY 0,5 MM, motor shaft 1,5 mm, rear axle 3/32"
Convenient tool for accurate and fast installation of the motor on F1: fixes the center of the motor shaft and the axis, after which the motor is soldered.
-
S&K F1 motor adjustment tool for offset crowns with 2 mm axle - #0104
CONDUCTOR FOR SET THE MOTOR ON F1, WITH THE CENTER SHIFTED DOWN BY 0,5 MM, motor shaft 1,5 mm, rear axle 2 mm
Convenient tool for accurate and fast installation of the motor on F1: fixes the center of the motor shaft and the axis, after which the motor is soldered.
-
WRIGHTWAY DIAMOND WHEEL SET, w/holder, 5 pcs. - #WWDCD
DIAMOND WHEEL SET, w/holder, 5 pcs. - #WWDCD
-
DUBICK Engineering F1 motor adjustment tool for crowns gears with 3/32" (2.36 mm) axle, 1.5 mm motor shaft and 0.2 mm offset
DUBICK Engineering F1 motor adjustment tool for crowns gears with 3/32" (2.36 mm) axle, 1.5 mm motor shaft and 0.2 mm offset
Special for 5 and 6 teeth 72 pitch pinions. 0.2 mm offset allow instal down F1 motor for more low center of gravity, but not so dangerous like 0.5 mm offset.
-
DUBICK F1 motor adjustment tool for crowns gears with 2 mm axle, 1.5 mm motor shaft and 0.2 mm offset - #DB711
DUBICK F1 motor adjustment tool for crowns gears with 2 mm axle, 1.5 mm motor shaft and 0.2 mm offset - #DB711
Special for 5 and 6 teeth 72 pitch pinions. 0.2 mm offset allow instal down F1 motor for more low center of gravity, but not so dangerous like 0.5 mm offset.
-
JConcepts Precision curved scissors, stainless steel blades, black handles - #2373
JConcepts Precision curved scissors, stainless steel blades, black handles
Cutting polycarbonate, soft plastic, soft rubber, fabric and thin paper products are what scissors are intended for.
-
PARMA CURVED SCISSORS FOR LEXAN - #10398
Curved Lexan Scissors
-
KOFORD ISRA TECH TOOL - M674
ISRA tech tool - EDM cut and anodized
-
PARMA ULTIMATE LEXAN SCISSORS - #10404
Utimate Body Scissors - Heavy duty 8" long scissors with 3.5" blades for cutting and trimming through thick RC bodies, wire, etc. No toolbox is complete without a set.
-
ZHB SET OF SMALL STEEL FILES W/DIAMOND COATING, 12 pcs.
Set of small steel files with diamond coating 12 pcs.
-
DUBICK SET OF STEEL PROBES FOR MEASUREMENT OF CLEARANCE, 20 pcs from 0,05 to 1 mm - #DB206
Thickness in set: - 0,05 mm/ 0,1 mm/ 0,15 mm/ 0,2 mm/ 0,25 mm/ 0,3 mm/ 0,35 mm/ 0,4 mm/ 0,45 mm/ 0,5 mm/ 0,55 mm/ 0,6 mm/ 0,65 mm/ 0,7 mm/ 0,75 mm/ 0,8 mm/ 0,85 mm/ 0,9 mm/ 0,95 mm/ 1 mm, respectively
The set is more than enough for the most detailed measurement of clearance!
-
JK Body Guide Cutting Tool - #L80
JK Body Guide Cutting Tool - #L80
Professional tool for easy & smooth cutting of the body
-
TAMIYA ANGLED TWEEZERS - #TAM74003
Special order!
These angled tweezers are useful for handling small parts and adding decals to your models. The edges are rounded to prevent scratching. Made from stainless steel with a black cationic finish for long life.
-
JKP Otoscope - Illuminated Commutator Inspection Tool - #L33
Otoscope - Illuminated Commutator Inspection Tool - Not For Medical Use -
-
ZHB SET OF SMALL STEEL FILES W/DIAMOND COATING, 10 pcs.
Set of small steel files with diamond coating 10 pcs.
-
JK Precision guide nut wrench for JK#U61 nut - #L30
JK Precision guide nut wrench for JK#U61 nut - #L30
-
KOLHOZA BODY CUTTING TOOL - KZA002
Professional tool for easy & smooth cutting of the body
-
KOLHOZA PIT BOX - KZA004
Pit Caddy for holding tires, traction, tools etc
-
LUCKY BOB GEAR PRESS - #LKY1000
GEAR PRESS (USED TO PRESS ON 7T THRU 11T GEARS)
-
KOLHOZA GUIDE SANDING TOOL - KZA011
Guide sanding tool
-
WRIGHT WAY Magnetic tech block - #WWMTB
WRIGHT WAY Magnetic tech block - #WWMTB
Phenolic Block with magnets for holding the car in place.
-
ATTAN Braid Cutter
Cut your braids to perfect length every time with this Braid Length Jig. Fully adjustable and beautifully made
-
ATTAN Pit box, pink
ATTAN Pit box, pink
3 slots for wheel tubes, 2 slots for tire wrenches, 3 slots for axles, 6 slots for braids, 2 big slots for the rest.
-
ATTAN Pit box, red
ATTAN Pit box, red
3 slots for wheel tubes, 2 slots for tire wrenches, 3 slots for axles, 6 slots for braids, 2 big slots for the rest.
-
ATTAN Gear holder (2 mm & 3/32" axles) for straightness checker for axle, rim & gear
ATTAN Gear holder (2 mm & 3/32" axles) for straightness checker for axle, rim & gear
-
ZHB Digital Calipers 150 mm (6"). Accuracy: +/- .02mm/.001inch. Plastic box and 2 pc battery.
Specs:
Range: 0-150mm
Accuracy: +/- .02mm/.001inch
Resolution: .01mm/0.0005inch
Repeatability: 0.01mm/0.0005inch
Max Measuring Speed: 1.5m/s, 60inch/s (FAST)
Operating Temp: 0~40Deg Celcius
Storage Temp: -10~60Deg Celcius
Power: 1.5v SR44 Battery -
JK Heavy Duty Pinion Gear Puller - #L23
JK Heavy Duty Pinion Gear Puller - #L23
DELUXE GEAR PULLER has tighter pin and is harder than the previous version. Made from tool steel.
Old catalog #JK8062
-
KA Donuts mounting tool
KA Donuts mounting tool
-
MID-AMERICA PRO billet tech block w/ 8 guide depths double sided - #MID417
MID-AMERICA PRO billet tech block w/ 8 guide depths double sided - #MID417
-
Slotracingshop.com Tire durometer w/protective hard shell plastic case
Tire durometer w/protective hard shell plastic case
-
KOLHOZA GUIDE TOOL - KZA001
Guide threading & Guide sanding tool in one
-
KOLHOZA DIAMOND DONUT DRILL 10MM DIA - KZA016
Diamond Donut drill 10 mm diameter - For opening up the hole on raw tire donuts.
-
KOLHOZA REAR WHEEL CUTTER Ø20MM - KZA010
Wheel well cutting tool - cuts rear wheel well at 20mm
-
KOLHOZA REAR WHEEL CUTTER Ø22MM - KZA0101
Wheel well cutting tool - cuts rear wheel well at 22mm
-
KOLHOZA Rear wheel cutter Ø26 mm - #KZA010-26
KOLHOZA Rear wheel cutter Ø26 mm - #KZA010-26
Wheel well cutting tool - cuts rear wheel well at 26 mm
-
KOLHOZA Rear wheel cutter Ø24 mm - #KZA010-24
KOLHOZA Rear wheel cutter Ø24 mm - #KZA010-24
Wheel well cutting tool - cuts rear wheel well at 24 mm
-
EAGLE Track braid roller tool - #EDP105
EAGLE Track braid roller tool - #EDP105
-
TWP EDM rear axle alignment tool - #TWP521
TWP EDM rear axle alignment tool - #TWP521
New Rear axle alignment with 9 height options. Cut to erosion with CNC wire. Extremely precise with 0.005 mm tolerance. For gears between 32 teeth up to 40 teeth with holes for 3/32 shafts. The 90 mm long shaft is not included.
-
VITULA End mill bore 2 mm - #T1250
End mills are made from special high speed steel and they are sharpened of CNC grinder. End mills are mounted in duralumin grip. These tools are intended only for manual machining of soft material components, not for steel.
-
VITULA End mill bore 3/32" (2,36 mm) - #T1252
End mills are made from special high speed steel and they are sharpened of CNC grinder. End mills are mounted in duralumin grip. These tools are intended only for manual machining of soft material components, not for steel.
-
SRP Pit caddy
SRP Pit caddy
Don't forget to choose the color!
- Dimensions: 180x130mm / 7x5 in.,
- runs off 9V battery,
- 2 spots for tire wrenches,
- 3 spots for oil/braid juice,
- small magnet for holding pins,
- slot for Lane Stickers,
- Color Options: Black, Blue, Green, Yellow, Red, Orange, Purple, Clear.
-
MS-SLOTPARTS Static balancer tool for balancing the hubs and gears of slot cars. Includes 3/32 " & 2 mm axles and storage box.
Static balancer tool for balancing the hubs and gears of slot cars.
Includes 3/32 " & 2 mm axles and storage box.
-
MID AMERICA Braid roller tool - heavy duty for commercial tracks - #MID415
MID AMERICA Braid roller tool - heavy duty for commercial tracks