Motors, Setups & Motor Parts
-
CAHOZA EUROSPORT 24 SETUP 20 SEGMENT FLAT, .450T x .300L - can ID .590 - #102-A
PARAMETERS
- Magnets quantity: 20 flat
- Outside dia.: .590" (15,00 mm)
- Magnets height: .448" (11,4 mm)
- Magnets length: .315" (8 mm)
- Endbells dia.: .570" (14,5 mm)
- Total length (including endbells, without post for ball bearing): .610" (15,5 mm)
- Setup designed for .485" armatures, vertical hardware #170, 5 coil anodised spring posts, long tower for PK arms (with commudator cap)
-
CAHOZA EUROSPORT 24 SETUP 24 SEGMENT FLAT, .450T x .300L - can ID .590 - #103
PARAMETERS
- Magnets quantity: 24 flat
- Outside dia.: .590" (15,00 mm)
- Magnets height: .448" (11,4 mm)
- Magnets length: .315" (8 mm)
- Endbells dia.: .570" (14,5 mm)
- Total length (including endbells, without post for ball bearing): .610" (15,5 mm)
- Setup designed for .485" armatures, vertical hardware #170, 5 coil anodised spring posts, long tower for PK arms (with commudator cap)
-
CAHOZA EUROSPORT 24 SETUP V 24 SEGMENT, .450T x .300L - can ID .590 - #103-A
PARAMETERS
- 24 segmented magnets – bevelled 15°
- Outside dia.: .590" (15,00 mm)
- Magnets height: .448" (11,4 mm)
- Magnets length: .315" (8 mm)
- Endbells dia.: .570" (14,5 mm)
- Total length (including endbells, without post for ball bearing): .610" (15,5 mm)
- Setup designed for .485" armatures, vertical hardware #170, 5 coil anodised spring posts, long tower for PK arms (with commudator cap)
-
CAHOZA EUROSPORT 24 SETUP V 28 SEGMENT, .450T x .300L - can ID .590 - #103-B
PARAMETERS
- 28 segmented magnets – bevelled 7°
- Outside dia.: .590" (15,00 mm)
- Magnets height: .448" (11,4 mm)
- Magnets length: .315" (8 mm)
- Endbells dia.: .570" (14,5 mm)
- Total length (including endbells, without post for ball bearing): .610" (15,5 mm)
- Setup designed for .485" armatures, vertical hardware #170, 5 coil anodised spring posts, long tower for PK arms (with commudator cap)
-
KOFORD ARMATURE ULTRASHORT FOR F1/32, WINDINGS 49/30, DIA. 0.465", STACK 0.235", ADVANCE ANGLE 28º, BALANCED, shaft lapping to 1.5 mm - M255EH (CUSTOM)
ARMATURE ULTRASHORT FOR F1/32, 49/30, BALANCED, H blank ultrashort custom Euro arm with angled comm tabs for F1
PARAMETERS:
- Wingings: 49/30
- Dia.: 0.465"
- Stack: 0.235"
- Long (by ballbearings): 0.664"
- Advance angle: 28
-
KOFORD ARMATURE ULTRASHORT FOR F1/32, WINDINGS 45/29, DIA. 0.459", STACK 0.235", ADVANCE ANGLE 18º, BALANCED, shaft lapping to 1.5 mm - M255EH (CUSTOM)
ARMATURE ULTRASHORT FOR F1/32, 45/29, BALANCED, H blank ultrashort custom Euro arm with angled comm tabs for F1
PARAMETERS:
- Wingings: 45/29
- Dia.: 0.459"
- Stack: 0.235"
- Long (by ballbearings): 0.664"
- Advance angle: 18
-
KOFORD ARMATURE ULTRASHORT FOR F1/32, WINDINGS 45/29, DIA. 0.465", STACK 0.235", ADVANCE ANGLE 18º, BALANCED, shaft lapping to 1.5 mm - M255EH (CUSTOM)
ARMATURE ULTRASHORT FOR F1/32, 45/29, BALANCED, H blank ultrashort custom Euro arm with angled comm tabs for F1
PARAMETERS:
- Wingings: 45/29
- Dia.: 0.465"
- Stack: 0.235"
- Long (by ballbearings): 0.664"
- Advance angle: 18
-
KOFORD ARMATURE ULTRASHORT FOR F1/32, WINDINGS 49/28, DIA. 0.465", STACK 0.235", ADVANCE ANGLE 20º, BALANCED, shaft lapping to 1.5 mm - M255EH (CUSTOM)
ARMATURE ULTRASHORT FOR F1/32, 49/28, BALANCED, H blank ultrashort custom Euro arm with angled comm tabs for F1
PARAMETERS:
- Wingings: 49/28
- Dia.: 0.465"
- Stack: 0.235"
- Long (by ballbearings): 0.664"
- Advance angle: 20
-
VALIKO ARMATURE S-arm (slot ceramic, blue), WINDINGS 45/29, DIA. 0.460", STACK 0.240", ADVANCE ANGLE 28º, BALANCED, shaft 1.5 mm
PARAMETERS:
- Type: C-arm
- Wingings: 45/29
- Dia.: 0.460"
- Stack: 0.240"
- Long (by ballbearings): 0.660"
- Advance angle: 28
- Arm.shaft: 1,5mm
-
ALPHA Teflon spring insulation, hank - #501
ALPHA Teflon spring insulation, hank - #501
The same bright red unmeltable spring insulation, but now with an even smaller outside diameter to allow that extra bit of room you need. It also slides on the spring more easily
-
B52 50,000rpm Mini Motor - #B52-50
B52 50,000rpm Mini Motor
Ball bearing at both ends, 50,000 rpm, super dynamic balance, best in the business bar none, close performance between motors
-
B52 50K ball bearing motor - #B5250KBB
B52 50K ball bearing motor - #B5250KBB
50,000 RPM ball bearing motor
-
B52 70K ball bearing motor - #B52-70KBB
B52 70K ball bearing motor - #B52-70KBB
-
B52 C-Can Bevelled magnets 0.167" thick, 0.458" long, type 3 (both side is bevelled), pair
B52 C-Can magnets, type 3, pair
-
B52 C-Can Combo magnets 0.167" thick, 0.458" long, type 1 (one side is flat one side is bevelled), pair
B52 C-Can magnets, type 1, pair
-
B52 C-Can Flat magnets 0.167" thick, 0.458" long, type 2 (both side is flat), pair
B52 C-Can magnets, type 2, pair
-
CAHOZA 12 magnets FORMEL 32 SET UP .376T x .256L - can ID .570 - #100
PARAMETERS
- Magnets quantity: 12
- Outside dia.: .580" (14,75 mm)
- Magnets height: .376" (9,6 mm)
- Magnets length: .255" (6,5 mm)
- Endbells dia.: .570" (14,5 mm)
- Total length (including endbells, without post for ball bearing): .567" (14.4 mm)
- For armatures dia.: .472" armatures, especially altered horizontal hardware, 3 coil anodised spring posts, endbell is milled on the bottom side so that this setup fits into all chassis, fits into Horky-Recek chassis
-
CAHOZA 16 magnets FORMEL 32 SET UP .376T x .256L - can ID .570 - #100-A
PARAMETERS
- Magnets quantity: 16
- Outside dia.: .580" (14,75 mm)
- Magnets height: .376" (9,6 mm)
- Magnets length: .255" (6,5 mm)
- Endbells dia.: .570" (14,5 mm)
- Total length (including endbells, without post for ball bearing): .567" (14.4 mm)
- For armatures dia.: .472" armatures, especially altered horizontal hardware, 3 coil anodised spring posts, endbell is milled on the bottom side so that this setup fits into all chassis, fits into Horky-Recek chassis
-
CAHOZA 3 COIL MOTOR SPRINGS STEEL, pair - #255
3 COIL STEEL SPRINGS
Cahoza springs for G12, Cobalt 12, INT15, G27 motors and G7 qualification motors, made from hardened steel coated with white shiny zinc, withstands 800F, these springs have got 8% more tension than the stainless steel springs -
CAHOZA 3 COIL SPRINGS STAINLESS STEEL, pair - #254
3 COIL SPRINGS
Cahoza springs for G12, Cobalt 12, INT15 motors, made from stainless steel, resists up to 800F, these springs have got the same tension as Red Champion, but the quality and workout is far more professiona -
CAHOZA 5 COIL SPRINGS, pair - #CAH160
5 COIL SPRINGS
Cahoza springs for Scale motors and G27 motors, made from hardened steel coated with white shiny zinc, withstands 800F, high quality and accuracy -
CAHOZA 5 coil stainless steel springs, 1 pair - #161
CAHOZA 5 coil stainless steel springs, 1 pair - #161
Cahoza springs for Scale motors and G27 motors, made from stainless steel, resists up to 800F
-
CAHOZA Aluminium nickel plated brush hoods, 1 bag (6 pairs) - #266
CAHOZA Aluminium nickel plated brush hoods, 1 bag (6 pairs) - #266
hardware (brush hoods), made from hard aluminium plate with thickness of 0.4mm (.0157"), nickel plated, hand work, most precise, no more grinding or drilling
-
CAHOZA ALUMINUM ANODISED SPRING POST /3 COIL,1 pair - #154
ANODISED SPRING POSTS - 3 COIL SPRINGS
aluminium anodised spring posts for 3 coil springs, spring post do not fit Cahoza plastic G12 endbells, suitable for hardware #170 and #171, packaged 10 pairs per bag