FRONT WHEEL STICKERS, set for 20 bodies, cut out along the counter - #006

Very convenient stickers for preparing your bodies for the passage of a technical commission

DOSLOT Sticker Racing Numbers Isra, 3 e.a. 

Sheet length 115 mm (4.527"), numbers heigh is 7.6 mm (.299")

ALP903 -RACING APRONS - full apron, High quality, bright red aprons with the Alpha Logo

KOALA CLAWS 

The ultimate tire traction additive! Used by Champions! Super thin and does not hold the car back but provides great grip throughout the race. Just massage into tyres before the race. Suitable for Sponge and solid rubber scale tyres.

Professional tool for easy & smooth cutting of the body

Pit Caddy for holding tires, traction, tools etc

JK Tire rack - #L32

Wheel stand is for holding any kind of tires.

RED FOX Clear body Production 1/24 Mercedes ISRA LEGAL FOR ISRA 2026

• Made from: Polycarbonate (Lexan)
• For: Production 1/24
• Thickness: .007" (0.175 mm)
• Clear body, with paint mask

DoSlot Brushless motor 1105 2000kv, 12-pole,  2 mm shaft

Motor details:
- Cable with kink protection
- Motor with ball bearings, maintenance-free!
- Motor shaft diameter 2mm, length 10mm (with new motor holder, the motor can be exchanged 1:1 for common 13D and 18D motors
- Motor diameter approx. 14mm, motor length approx. 13mm
- Weight with cable and plug approx. 6.2g

DUBICK Reinforcement tape for pin hole, 30 x 180 mm (1,18" x 7,1") - #707

MID AMERICA Gear 64 pitch, 31T, 0° angle, 3/32" axle, Ø13.06 mm, w/screw - #MID16431

BSR Motor mount for ES 1/24 chassis, made for 2.36x4.76 mm axle ballbearings

EUROSPORT 1/24 Audi 2019-2021 ISRA LEGAL Body 

• Made from: Polycarbonate (Lexan)
• For: Eurosport 1/24
• Thickness: .005" (0.125 mm)
• ISRA legal body for 2019-2021 years

RED FOX Clear Body Formula 1/32 Ferrari F1 HALO LEGAL FOR ISRA 2023-2026

• Made from: Polycarbonate (Lexan)
• For: Formula 1/32
• Thickness: .005" (0.125 mm)
• Clear body

DUBICK gold plated short guide clips. Made special for new RED FOX guides. (But also fit for all other guides), 1 pair (NEW!)

Ø1.16 MM FRONT AXLE, CARBON, (length ~ 80 mm) used in Production 1/24 & Production 1/32 for made forward track with smal ribber wheels

PARMA Brushless motor 3000KV - #1302

PARMA Brushless motor 4500KV - #1304

PARMA Brushless motor 6500KV - #1306

DOSLOT Sticker Front Wheels, set for 10 bodies

Front wheels sticker diameter is 13.2 mm (.520")

DOSLOT Sticker Delta Plastic Hyundai, set for 1 body

Sheet length 40 mm (1.575")

DOSLOT Sticker Attan Tesla, set for 1 body

Sheet length 105 mm (4.134"), front wheels sticker diameter is 13.2 mm (.520")

DOSLOT Sticker Redfox Audi R10 1/24, set for 1 body

Sheet length 70 mm (2.756"), front wheels sticker diameter is 13.2 mm (.520")

The price of assembling the model includes the installation of the motor, together with the soldering of the pinion and the setting of the pinion-gear position, the installation of a guide, lead wires, ballbearings or oilities and tubes for pins, if necessary.

Any configuration is possible!!!!!

DOSLOT Stickers F1 "Petronas", set for 1 body

FEATURES: Fuel-Proof, Water Based Formula For Easy Clean-Ups. Many Colors For Painting Slot and R/C Car Bodies, Plastic Models. Pinewood Derby Cars, Boats, Scenery, Signs and Ceramics. It remains flexible and resists cracking, chipping and impact damage. Can be used with any air-brush that delivers over 40 to 70 psi, and Uses a MEDIUM tip.

Heat transfer compound.

Apply between brush and hood on motors to reduce comm temperatures and increase reliability, also especially effective for removable soldering iron tips.

JK MOTOR BRACKET CHEETAH 25 CHASSIS, 1 pc. - #C40B

Old catalog #JK250115

TWP Pin body harpoon - #TWP-PIN 

Convenient tool for the body preparing!

SLICK7 Wheel retainer eyelets .032", 1 pack (10 pcs.) - #S7-140

Small eyelett retainer for holding .032" axle wheels onto axle. Use with S7-143 rubber wheels or S7-345 rubber wheel. Made from thin wall brass for min. weight. Fits over body pin axles.

SLICK7 Wheel retainers 1/16" axle, 1 pack (4 pcs.) - #S7-129

DUBICK Lead sheet thickness 0.5 mm, 50 х 50 mm (.019", 1.968" x 1.968") with a 3M selfstick adhesive tape - #209

Lead sheet thickness 0.5 mm, 50 х 50 mm with a adhesive tape can help you to configure your chassis. 
The presence of stick layer eliminates the need for glue application and simplifies the work!

K&S Brass strip .016" x 1/4" x 12" (0.41 mm x 6.35 mm x 300 mm) - #KS8230

NeAn Box for storage KV tire truer 4,33"x3,54"x2,75" (110x90x70 mm) - #170

Plastic box comes with the tire truers KV (KV #1, KV #4)

Guide threading & Guide sanding tool in one

Alignment bar with holes, provided with centering holes for both vertical and horizontal style brush hoods. The essential tool for motor assembly, used by motor builders world wide

EAGLE High performance controller handgrip - #ET-1

Grip fits Parma, Red Fox, JK and DiFalco Controller handles

The handgrip measures approximately 95 millimetres (3.74") in length.

PARMA steel 2 piece chassis is designed with a floating top pan for best handling and performance. A lightweight aluminum top pan is also available for more speed and faster cornering. 4" wheel base.

PARMA steel 2 piece chassis is designed with a floating top pan for best handling and performance. A lightweight aluminum top pan is also available for more speed and faster cornering. 4" wheel base.

BSR Motor mount for ES 1/32, made for 2x5 mm axle ballbearings

BSR Motor mount for F1/32 chassis, made for 2x5 mm axle ballbearings, motor dia. 12.2 mm

• Robust construction guarantees stable motor positioning.

BSR Motor mount for F1/32 chassis, made for 2x5 mm axle ballbearings, motor dia. 13.5 mm

• Robust construction guarantees stable motor positioning.

BSR Motor mount for F1/32 chassis, for 4 and 3 hole stators in one, motor dia. 14.0 mm

4 holes version same as previously, made for 2x5 mm axle ballbearings, motor dia. 14.0 mm

3 holes made for screws 0/80" (classic cans screws).

MID-AMERICA 1/24 Brushless motor bracket (JK, Mossetti, etc) - #MID223

MOSSETTI Outboard shaft support for brushless motors - #MR1062

Use 5 mm bushing/bearing

ZHB Screw for mount brushless motor, M2x3 mm, hex 1.5 mm, 1 pc.

Made from stainless steel 304 (A2-70), high quality steel

Includes travel bag with wheels.

Width - 430 mm (17,3"); Height - 310 mm (12,6"); Depth - 195 mm (7,87")

All small boxes, as in the photo, are included. This sizes are good to the norms of hand luggage, so you can take the box to the cabin, which is very convenient for travels. There is no built-in lighting. All box have department for 1/32 and 1/24 models and for tools.

Cost of delivery are discussed individually

INTERIOR FOR "TEAPOT" 1/24 BODIES

ZHB Any gear glued on axle - #113

In price included: gear, axle and work.

You can choose any gear from the stock and axle (EDM hollow axles are not included!)

ZHB Any gear glued on EDM hollow axle - #114

In price included: gear, axle and work.

You can choose any gear from the stock and EDM hollw axle only.

PARAMETERS

• Material: Transparent plastic
• Dimension, mm: 133×78×16
• Quantity of sections, pcs.: 12

MID-AMERICA Guide nut socket driver (metric nuts) - #MID129M

KOFORD Ø1.5 mm x 1.58" (40.1 mm) ultra precision axle for eurosport - #M760

TAMIYA 1/14 R/C Buggyra Fat Fox (TT-01 Type-E)

For more information click here: https://www.tamiya.com/english/products/58661/index.htm

CHAMPION 1/24 Turbo-flex RTR 16D motor - Outlaw body - #CHA109A

PARMA 16D Cruiser motor sealed - balanced - .560" dia. armature - #701

Tool for mounting tire donuts onto the rim

Comes with axes 3/32" & 2 mm

DUBICK gold plated long guide clips. Made special for new RED FOX guides. (But also fit for all other guides), 1 pair

JK STIFFER BRAID, pair - #U11 

Stiffer braid for guide, pair

Sizes: 0,8 x 4,8 x 27,5 mm (.0315" x .189" x 1.083")

Old catalog #JK35212

JK SOFT BRAID, pair - #U10 

Soft braid for guide, pair

Sizes: 0,9 x 4,85 x 32 mm (.035" x .191" x 1.26")

Old catalog #JK3521

The best choise for class Formula 1/32

MID AMERICA 456 Braid, pair - #MID405

Sizes: 4.4 mm x 0.9 mm (.173" x .035")

Heavy duty thick braid .with 456 strands of wire

MID AMERICA 456 Braid, 30 pr. - #MID405

Sizes: 4.4 mm x 0.9 mm (.173" x .035")

Heavy duty thick braid .with 456 strands of wire

RED FOX Braid thin & wide, silver plated, 1 pair - #RFBRAIDW

WRIGHTWAY Body pin punch - #WW90

Body Pin Punches are for making pin holes in bodies.

JK Gear 64 pitch, 32T, 0° angle, 3/32" axle - #G632

Old catalog #JKG632

ZHB LANE STICKERS, set for race

Lane stickers for model, from 1 to 8 lane

K&S Round brass tube 3/32" x .014" x 12" (2.36 mm x 0.355 mm x 304.8 mm), 1 pack (3 pcs.) - #KS8126

DOSLOT Sticker Redfox Audi R10 1/32, set for 1 body

Sheet length 60 mm (2.362"), front wheels sticker diameter is 13.2 mm (.520")

ASSOCIATED STEEL SCREW M2 X 8 MM W/COUNTERSUNK HEAD, for Phillips-head screwdriver, 1 pc. - #25196

STEEL NUT M2, 1 pc.

Steel nut for fixing guides

DUBICK 61/39 QUALITY SOLDER in storage tube, diameter 1mm, long 6 feet (1.8 m), 1 pc. - #211

2mm ultraprecision premium plated axles for Eurosport made using ultrahigh strength steel and plated and ground. One per package

CHAMPION Clear Body 4.5" Dirt Late Model

• Made from: Polycarbonate (Lexan)
• For: 4.5"
• Thickness: .015" (0.381 mm)
• Clear body

CHAMPION Clear Body 4.5" Offset Late Model

• Made from: Polycarbonate (Lexan)
• For: 4.5"
• Thickness: .015" (0.381 mm)
• Clear body

Clear body Production 1/24 Ferrari FXX

• Made from: Polycarbonate (Lexan)
• For: Production 1/24
• Thickness: .007" (0.175 mm)
• Clear body, w/paint masks

Body Production 1/24 Mclaren 650S GT3

• Made from: Polycarbonate (Lexan)
• For: Production 1/24
• Thickness: .007" (0.175 mm)

FEATURES: Fuel-Proof, Water Based Formula For Easy Clean-Ups. Many Colors For Painting Slot and R/C Car Bodies, Plastic Models. Pinewood Derby Cars, Boats, Scenery, Signs and Ceramics. It remains flexible and resists cracking, chipping and impact damage. Can be used with any air-brush that delivers over 40 to 70 psi, and Uses a MEDIUM tip.

PARMA Super 16D big daddy motor sealed - balanced - .560 dia. armature - #702

DOSLOT Stickers F1 "Brawn", set for 1 body

KOFORD Ø.471" (11.96 mm) bearing assembly tool (for Eurosport motor) - #M523-471

Prepare your motor fast & precise. Short length just for Euro set ups.

This is no actual photo! Actual photo will be added later!

KOFORD Ultralight qualifying wire, 1 pc. - #M383

The Nat’s TQ ultralight qualifying lead wire made from ML magnet wire. Enough for several cars.

Includes 3/32 " & 2 mm axles and reserve rubber transmission belt

MID AMERICA 1/24 Champion Turbo-Flex steel chassis - #MID215

3/32" (2.36 MM), .005" (0.127 MM) THICK, STEEL AXLE SPACERS, 10 pcs.

PARAMETERS

• Material: Transparent plastic
• Dimension, mm: 145×232×23

CHAMPION Clear body 1/24 Porsche with wings

• Made from: Polycarbonate (Lexan)
• For: 1/24 scale (4")
• Thickness: .007" (0.175 mm)
• Clear body

JK Clear body 4" Lamborghini SC63 GTP - #B169A

• Made from: Polycarbonate (Lexan)
• For: 1/24 scale (4")
• Thickness: .007" (0.175 mm)
• Clear body

JK Clear body 4" Audi RSC 99 - #B86X 

• Made from: Polycarbonate (Lexan)
• For: 4"
• Thickness: .005" (0.125 mm)
• Clear body

Old catalog #JK7182

Heavy tire traction. The choice of the Pro's.

MS-SLOTPARTS Gauge for cutting the braids

Through the set dimension, cutting is always precisely at the same length. Unequal or cropped braids belong to the past. 

Updated configuration!

Body Production 1/24 Mclaren 650S GT3

• Made from: Polycarbonate (Lexan)
• For: Production 1/24
• Thickness: .005" (0.125 mm)

MOSSETTI Patriot "Revolver" chassis - flat track version - for brushless - #MR4002

With outboard shaft bearing support included 

DoSlot Brushless motor 1105 3000kv, 12-pole, 2 mm shaft 

Motor details:
- Cable with kink protection
- Motor with ball bearings, maintenance-free!
- Motor shaft diameter 2mm, length 10mm (with new motor holder, the motor can be exchanged 1:1 for common 13D and 18D motors
- Motor diameter approx. 14mm, motor length approx. 13mm
- Weight with cable and plug approx. 6.2g

DoSlot Brushless motor 1105 4000kv, 12-pole, 2 mm shaft

Motor details:
- Cable with kink protection
- Motor with ball bearings, maintenance-free!
- Motor shaft diameter 2mm, length 10mm (with new motor holder, the motor can be exchanged 1:1 for common 13D and 18D motors
- Motor diameter approx. 14mm, motor length approx. 13mm
- Weight with cable and plug approx. 6.2g

DoSlot Brushless motor 1105 6000kv, 12-pole, 2 mm shaft

Motor details:
- Cable with kink protection
- Motor with ball bearings, maintenance-free!
- Motor shaft diameter 2mm, length 10mm (with new motor holder, the motor can be exchanged 1:1 for common 13D and 18D motors
- Motor diameter approx. 14mm, motor length approx. 13mm
- Weight with cable and plug approx. 6.2g

DoSlot Brushless motor 1105 9000kv, 12-pole, 2 mm shaft 

Motor details: 
- Cable with kink protection
- Motor with ball bearings, maintenance-free!
- Motor shaft diameter 2mm, length 10mm (with new motor holder, the motor can be exchanged 1:1 for common 13D and 18D motors
- Motor diameter approx. 14mm, motor length approx. 13mm
- Weight with cable and plug approx. 6.2g

ZHB Screw for mount brushless motor, M2x3 mm, hex 1.5 mm, 1 cd. (10 pcs.)

Made from stainless steel 304 (A2-70), high quality steel

DoSlot Brushless motor 1105 11000kv, 12-pole, 2 mm shaft 

Motor details:
- Cable with kink protection
- Motor with ball bearings, maintenance-free!
- Motor shaft diameter 2mm, length 10mm (with new motor holder, the motor can be exchanged 1:1 for common 13D and 18D motors
- Motor diameter approx. 14mm, motor length approx. 13mm
- Weight with cable and plug approx. 6.2g

DoSlot E-Com chip "White - Frankie edition - Aggressive" 

DoSlot E-Com Chip - Frankie Edition - Details:
- With reverse polarity protection of the most sensitive components
- Minimum "starting voltage" - approx. 1.7V
- Maximum voltage - approx. 17V
- Size - approx. 25x17mm
- Weight - approx. 1.6g (without cable)

Body 1/24 Chevrolet Pick-Up (1951)

• Made from: Polycarbonate (Lexan)
• For: Production 1/24
• Thickness: .007” (0.175 mm)

DoSlot Brushless motor 10.5-03 13000kv, 12-pole, 2 mm shaft 

This DoSlot brushless motor is significantly smaller than all other DoSlot 1105 motors.
At 13.2mm in diameter, it sits exactly between the 10xx and 11xx sizes, making it perfect for "Isra" Formula Inline slot cars.

Motor details:
- Ball bearing motor, maintenance-free!
- Motor shaft diameter 2mm, length 10mm (with new motor mounts, the motor can be exchanged 1:1 for common 13D and 18D motors)
- Motor diameter approx. 13.2mm, motor length approx. 11mm
- Weight with cable and connector approx. 4.2g

DoSlot Brushless motor 1105 17500kv, 6-pole, 1.5 mm shaft

Motor details:
- Cable with kink protection
- Motor with ball bearings, maintenance-free!
- Motor shaft diameter 2mm, length 10mm
- Motor shaft for the motor pinion reduced to 1.5mm!
- Motor diameter approx. 14mm, motor length approx. 13mm
- Weight with cable and plug approx. 6.2g

DoSlot Brushless motor 1105 18500kv, 12-pole, 1.5 mm shaft

Motor details:
- Cable with kink protection
- Motor with ball bearings, maintenance-free!
- Motor shaft diameter 2mm, length 10mm
- Motor shaft for the motor pinion reduced to 1.5mm!
- Motor diameter approx. 14mm, motor length approx. 13mm
- Weight with cable and plug approx. 6.2g

DoSlot Brushless motor 1105 21500kv, 6-pole, 1.5 mm shaft

Motor details:
- Cable with kink protection
- Motor with ball bearings, maintenance-free!
- Motor shaft diameter 2mm, length 10mm
- Motor shaft for the motor pinion reduced to 1.5mm!
- Motor diameter approx. 14mm, motor length approx. 13mm
- Weight with cable and plug approx. 6.2g

RALPH THORNE Clear Body 1/24 High down force ORCA

• Made from: Polycarbonate (Lexan)
• For: 1/24 scale
• Thickness: .007" (0.175 mm)
• Clear body

CHAMPION Clear Body 1/24 4" Buick Regal IMSA Stock Car 1985

• Made from: Polycarbonate (Lexan)
• For: 1/24 scale
• Thickness: .007" (0.175 mm)
• Clear body w/paint masks

RALPH THORNE Clear Body 4" Evolution dirt late modified, Lexan .007" (0.175 mm) - #1278A

• Made from: Polycarbonate (Lexan)
• For: 4"
• Thickness: .007" (0.175 mm)
• Clear body

RALPH THORNE Clear Body 1/24 4" Titan Stock Car

• Made from: Polycarbonate (Lexan)
• For: 1/24 scale
• Thickness: .005" (0.125 mm)
• Clear body

RALPH THORNE Clear Body 1/24 4" Titan Stock Car

• Made from: Polycarbonate (Lexan)
• For: 1/24 scale
• Thickness: .007" (0.175 mm)
• Clear body

RALPH THORNE Clear Body 1/24 4" Titan COT Stock Car

• Made from: Polycarbonate (Lexan)
• For: 1/24 scale
• Thickness: .007" (0.175 mm)
• Clear body

Bigger rear wing then the Titan

BPA Clear Body Eurosport 1/24 BMW LMR

• Made from: Polycarbonate (Lexan)
• For: Eurosport 1/24
• Thickness: .005" (0.125 mm)
• Clear body

RED FOX Clear Body 1/24 4" Bettle Wing HD

• Made from: Polycarbonate (Lexan)
• For: 1/24 scale
• Thickness: .007" (0.175 mm)
• Clear body

DoSlot E-Com chip "White" 1,5 seit "N"

Description:

-Special for 6M Motors and Eurosport Cars - ISRA 2026 ES24 and ES32 Title
- Less Motor temperature
- Can have little delayed start

SLICK7 Gear 48 pitch, 26T, 1/8" axle, Ø14.8 mm - #S7-525-26

KOLHOZA 1/24 Custom painted car interior, blue, thin .005" (0,125 mm) - #0126-blue

KOFORD Ø.476" (12.09 mm) bearing assembly tool (for Eurosport motor) - #M523-476

Prepare your motor fast & precise. Short length just for Euro set ups.

This is no actual photo! Actual photo will be added later!

KOFORD Ø.478" (12.14 mm) bearing assembly tool (for Eurosport motor) - #M523-478

Prepare your motor fast & precise. Short length just for Euro set ups.

This is no actual photo! Actual photo will be added later!

KOFORD Ø.479" (12.17 mm) bearing assembly tool (for Eurosport motor) - #M523-479

Prepare your motor fast & precise. Short length just for Euro set ups.

This is no actual photo! Actual photo will be added later!

KOFORD Ø.480" (12.19 mm) bearing assembly tool (for Eurosport motor) - #M523-480

Prepare your motor fast & precise. Short length just for Euro set ups.

This is no actual photo! Actual photo will be added later!

KOFORD Ø.481" (12.22 mm) bearing assembly tool (for Eurosport motor) - #M523-481

Prepare your motor fast & precise. Short length just for Euro set ups.

This is no actual photo! Actual photo will be added later!

KOFORD Ø.484" (12.29 mm) bearing assembly tool (for Eurosport motor) - #M523-484

Prepare your motor fast & precise. Short length just for Euro set ups.

This is no actual photo! Actual photo will be added later!

DoSlot E-Com chip "White" 1,5 seit "A"

One and a half side E-com chip agressive mode - 6 pole motors. ISRA 2025 World Champion in all Eurosport categories.

DoSlot E-Com chip "White" 1,5 seit "W"

Description:
- Universal E-Com
- ISRA 2026 F32 Title and Production 24 WarmUp Victory
- For all 12M motor till 18500KV
- Working with 6M motors, but maybe too high temperature
- Perfect Drag Racing E-Com
- Never any delay, perfect start
- More hot then other versions

DoSlot E-Com chip "White" 1,5 seit "Y"

One and a half side E-com chip - prototype Y.

Production 1/24 Audi body 

• Made from: Polycarbonate (Lexan)
• For: Production 1/24
• Thickness, mm: 0,125
• with paint mask

BSV LUXURY FISH donuts inside Ø 13.7 mm (.540"), outside Ø 24.1 mm (.949"), about 19.7 mm (.748") width, pair

LEAD WIRE 24Ga (section 0,21 mm²), yellow, 1 m

LEAD WIRE 24Ga (section 0,21 mm²), yellow, 1 m

Speed FX Group 12 Motor SRS C-Can - Black Endbell

Great option for the beggining racers in Production 1/24. When the work time of cheap armature came out, you can set in this can more expensive armature.

MID AMERICA Paste flux filled syringe, 1 pc. - #MID110

JK 4" Cheetah 21 chassis kit .035" C-Can - #C21 -

4” Cheetah 21 Stainless Steel Chassis Kit .035” thick with screw in Falcon motor brace

Old catalog #JK25021

JK 4" ISRA Production 1/24 brushless chassis kit w/J-bars, 0.039" front, 0.047" rear - #C95

Production 1/24 Audi body 

• Made from: Polycarbonate (Lexan)
• For: Production 1/24
• Thickness, mm: 0,175
• with paint mask

ARP Pinion 64 pitch, 6T, 0° angle, 1.5 mm bore, stainless steel - #ARP6406S1.5

PARMA Big Mama 408 braid, 1 pair - #663

Heavy duty braid (408 strands) for all slot cars. 1 Pair

PARMA Big Mama 408 braid, 10 pairs - #663

Heavy duty braid (408 strands) for all slot cars. Bag of 10 Pairs.

PARMA Big Mama 408 braid, 30 pairs - #663AA 

Heavy duty braid (408 strands) for all slot cars. Bag of 30 Pair.

PARMA Big Mama 408 braid, 100 pairs - #663B

Heavy duty braid (408 strands) for all slot cars. 100 Pairs

TAMIYA 1/14 R/C Team REINERT Racing MAN TGS (TT-01 Type-E) - #58642

Specifications
★Length:438mm, Width: 190mm, Height: 207mm ★Wheelbase: 257mm ★Tire Width/Diameter: 28/70mm ★Bathtub Type Chassis Frame ★Longitudinally-Mounted Motor Shaft-Driven Full-Time 4WD ★F/R 3-Bevel Differentials ★3-Piece Steering Tie-Rod ★4-Wheel Double Wishbone Suspension ★F/R Friction Dampers ★Gear Ratio=8.35:1 ★Type 540 Motor ★Requires an Electronic Speed Controller (sold separately)

RED FOX High performance 408 strand braid, 1 pair. - #RFBRAIDHP1

sizes: 5.1 mm x 0.9 mm (.200" x .035")

High Performacne 408 strand dimpled braid

Innovative controller EVO-3 from DenVel Electronics, new design

Manual in pdf -> Manual_Evo-3_eng

Innovative controller EVO-2 by DenVel electronics.
A lot of abslutly new moments below about few much important

• controller is regulator electric current
• 128 bands (speeds) - it make it really stable, soft and fast on corners
• wire chock 25 position
• Traction-control, By-pass,
• Works with brushless motors,
• Three type of brakes
• Dual Brake function - facilitates control in bundles of turns
• 6 cells of non-volatile memory by classes
• Possibility to chose comfortable place for trigger
• Adjustable trigger angle

These round polyethylene plastic snap lid containers with foam are though and strong. They are great for protection cans and setups when mailing them for service.

BSR Customized brushless motor rotor w/12 Magnets

Built on a DOSLOT rotor, this customized version features:

• Precision shaft: a replaced shaft, ground to 1.5 mm.

• Titanium reinforcement: the shaft mount is reinforced with a titanium insert for enhanced durability.

• Professional balancing: dynamically balanced to ensure ultra-smooth performance at high RPMs.

DOSLOT Brushless motor shaft 2mm, for the pinion reduced to 1.5mm

Shaft length 1.043" (26.5 mm)

CHICAGOLAND RACEWAY Aluminum guide collar, 1 pc.

SET OF SCREWS DIDN'T INCLUDED!!

For racers who don't need the lowest guide nut possible, for body clearance, these .150" tall, dual set screw, collars, don't require threading, and install almost effortlessly, with no wobble, using a standard tire wrench.

CAHOZA Low profile cut down nylon guide, w/out thread - #27

Сut down guide for integral guide tongue chassis, content: violet nylon, glass fibre, these guides have higher content of glass fibre, they are more tough, ideal for Production chassis and other groups

REAR WHEEL TIRES "MICROPORE", ID 9,5 mm, OD 25 mm, pair

Suitable for the model with any height of the rear axle, if necessary, you need to remove the "crust" on the machine for processing tires or lathe.

PARAMETERS

• Inside dia., mm: 9,5
• Outside dia., mm: ~ 25
• Width, mm: 22

This tires cut for GM & F1/24 (Nesterenko)

DUBICK Tire truer

New tire truer with on / off button, made with two types of needle trimming in diameter, three spacers 16 mm, 20 mm, 20.7 mm, a limb for setting the diameter as on a micrometer, a reduced size and weight. Comes with a storage bag.  

Magnetize possible any magnets from ferrite to samarium-cobalt

PARAMETERS

• Material: Transparent plastic
• Dimension, mm: 50×45×15
• Quantity of sections, pcs.: 1

Big head pro body pins. Ideal length for bending over on swing over front body mounts, or for use on with full width body mounts. Custom made just for us, the best on the market. 48 pins per package.

DUBICK gold plated guide clips with crimping for wires. Made for new RED FOX guides.(Fit for all other guides), 1 pair

MID AMERICA Lead wire 22Ga (section 0,33 mm²), clear, ultra flexible, ultra lite, 3 m (10 ft) - #MID140B

JK Gear 64 pitch, 35T, 0° angle, 2 mm axle, Ø14.53 mm, w/screw- #G635m

Old catalog #JK42352

JK Gear 64 pitch, 35T, 0° angle, 2 mm axle, Ø14.53 mm, w/screw, 1 cd. (6 ea.) - #G635m

Old catalog #JK42352

JK Gear 64 pitch, 37T, 0° angle, 2 mm axle, Ø15.35 mm, w/screw- #G637m

Old catalog #JK42372

JK Gear 64 pitch, 37T, 0° angle, 2 mm axle, Ø15.35 mm, w/screw, 1 cd. (6 ea.) - #G637m

Old catalog #JK42372

RALPH THORNE Clear Body 1/24 GTP Revolution

• Made from: Polycarbonate (Lexan)
• For: 1/24 GTP
• Thickness: .007" (0.175 mm)
• Clear body

RALPH THORNE Clear Body 1/24 GTP Warrior, Lexan .005" (0.125 mm) - #WARRIOR005

• Made from: Polycarbonate (Lexan)
• For: 1/24 GTP
• Thickness: .005" (0.125 mm)
• Clear body

RALPH THORNE Clear Body 1/24 GTP Warrior, Lexan .007" (0.175 mm) - #WARRIOR007

• Made from: Polycarbonate (Lexan)
• For: 1/24 GTP
• Thickness: .007" (0.175 mm)
• Clear body

PARMA Paint mask 1/32 & 1/24 graphics design - #792

SRP Pit caddy

Don't forget to choose the color!

• Dimensions: 180x130mm / 7x5 in.,
• runs off 9V battery,
• 2 spots for tire wrenches,
• 3 spots for oil/braid juice,
• small magnet for holding pins,
• slot for Lane Stickers,
• Color Options: Black, Blue, Green, Yellow, Red, Orange, Purple, Clear.

1/24 Toyota Celica Turbo 4WD Body

• Made from: Polycarbonate (Lexan)
• For: "TEAPOT" 1/24
• Thickness: .01" (0.25 mm)
  • Clear body, with paint mask

Retro Formula 1/24 Lotus 63 body 

• Made from: Polycarbonate (Lexan)
• For: Retro 1/24
• Thickness: .010" (0.254 mm)

JK MOTOR BRACKET CHEETAH 25 CHASSIS, 1 pc. - #C40B

Old catalog #JK250115

MOSSETTI Patriot motor braces, 2 pcs. (fits jk) - #MR-1050

Spring steel .050" thick - nickel plated

PARMA 1/24 CHASSIS COTTER PIN for CHAMPION TURBOFLEX CHASSIS, 1 pc.

.050" ALLEN WRENCH, W/OUT HANDLE, Г-type look

The simplest & cheap allen wrench for the beginning racers!

JK Body Guide Cutting Tool - #L80

Professional tool for easy & smooth cutting of the body

MID AMERICA Body mounting fixture for Gemini and JK Aeolos chassis - #MID456

JK Precision machined 6 hole guide nut, PRO-version. Use with the JK#L30 guide nut tool - #U61

JK Precision machined 6 hole guide nut, PRO-version. Use with the JK#L30 guide nut tool - #U61

Standard allen wrench for wheel screws, etc.

JK Donut wizard mounting tool - #L19 

Makes fitting of donuts easy.
Suitable for all 3/32" axle hubs / rims.
The wizard comes with 5 cones to suit most wheel sizes 8mm to 15mm
Manufactured from strong sturdy Nylon & Delrin with a hard steel 3/32" axle

Old catalog #JK8075

Specs:
Range: 0-150mm
Accuracy: +/- .02mm/.001inch
Resolution: .01mm/0.0005inch
Repeatability: 0.01mm/0.0005inch
Max Measuring Speed: 1.5m/s, 60inch/s (FAST)
Operating Temp: 0~40Deg Celcius
Storage Temp: -10~60Deg Celcius
Power: 1.5v SR44 Battery

JK 2mm Shaft, 0.050" HRC Hardened Precision Tolerance Allen Tip - #L14

Old catalog #JK8051

 Improved reduced diameter insert for the above wrench, also fits all standard handles

RALPH THORNE Clear Body 1/24 GTP Renegade, Lexan .007" (0.175 mm) - #RENEGADE007

• Made from: Polycarbonate (Lexan)
• For: 1/24 GTP
• Thickness: .007" (0.175 mm)
• Clear body

DUBICK 2026 ES 1/32 Eurosport chassis assembled w/out ballbearings, for brushless motor - #322026

All chassis starting from 2016 will be made of German high-carbon structural steel 1 mm thick. This is the same material that is used the world's leading chassis manufacturers.

Ballbearing 1 х 3 х 1 mm open , 6 balls - 1 Pc.

Reserve shielded ballbearing 3x7 mm for TIRE TRUERS KZA006, KZA0061

PARAMETERS

• Material: Transparent plastic
• Dimension, mm: 75×60×18
• Quantity of sections, pcs.: 6
• *For small parts

NeAn Clear body GM 1/24 Ford Cargo

• Made from: Polyvinyl chloride (PVC);
• For: GM (Truck);
• Thickness: .015" (0.4 mm);
• Width: 3.464" (88 mm);
• Height: 3.543" + .236" (90 + 6 mm);
• Wheelbase: 4.724" (120 mm);
• Wheels dia., till: till 1.417" (36 mm); 

Clear body, with paint mask

RALPH THORNE Clear Body 1/24 GTP Viking, Lexan .007" (0.175 mm) - #VIKING007

• Made from: Polycarbonate (Lexan)
• For: 1/24 GTP
• Thickness: .007" (0.175 mm)
• Clear body

RALPH THORNE Clear Body 1/24 GTP Viking, Lexan .010" (0.254 mm) - #VIKING010

• Made from: Polycarbonate (Lexan)
• For: 1/24 GTP
• Thickness: .010" (0.254 mm)
• Clear body

Air Control Kit including .014" Diaplane, .004" Skirted Side Dams and .004" Rear Spoiler

SLICK7 LEAD WIRE 21Ga (section 0,41 mm²), yellow, 1 m (3 ft), insulation diameter .066" (1,67 mm) - #S7-546

Very soft & thin lead wire. 

The best chooise for Formula 1/32!

H&R Jack Rabbit motor 14,000 rpm - #MJR1

Mabuchi Replacement Type - Double ended Plain 2mm shaft

Tire durometer w/protective hard shell plastic case

MID AMERICA Eagle retro motor - #MID606

SLICK7 Steel arm spacers .003" (0,076 mm), 10 psc. - #SL7-20

JK 3/32" (2.36 mm), .010" (0.254 mm) thick, stainless steel axle spacers, 10 pcs. - #U72-10

BSV Crown gear 48 pitch 26T, 3/32" axle,  Ø16.7 mm - #BSV0726

ISRA legal torsion for  JKP 4" CHEETAH X25 KIT 0.9MM THICK chassis for PRODUCTION 1/24- #JKPX25. 
Allows you to quickly disassemble and assemble the chassis and still remains flat.

NeAn Clear body GM 1/24 Scania

• Made from: Polyvinyl chloride (PVC);
• For: GM (Truck);
• Thickness: .015" (0.4 mm);
• Width: 3.464" (88 mm);
• Height: 3.543" (90 mm);
• Wheelbase: 4.724" - 6.889" (120 -175 mm);
• Wheels dia., till: till 1.417" (36 mm); 

Clear body, with paint mask

REAR WHEEL TIRES "MICROPORE", ID 9,5 mm, OD 33 mm, pair

Suitable for the model with any height of the rear axle, if necessary, you need to remove the "crust" on the machine for processing tires or lathe.

PARAMETERS

• Inside dia., mm: 9,5
• Outside dia., mm: ~ 33
• Width, mm: 22

This tires cut for GM & F1/24 (Nesterenko)

ALPHA Rear wheel donuts GREEN, treated, pair - #GREENT

1 pair of green treated tires for Production 1/32 or other classes

FX 2 X 5 Can & Endbell Replacement Oilites 

H&R Hawk motor I 18,000 rpm @12V- double shaft - #MH1

ALPHA Rear wheel donuts GREEN, pair - #GREEN

1 pair of green tires for Production 1/32 or other classes

Koford Yellow spoiler sticker, 1 pc. - #M719

Decorate your body with branded stickers :)

KOFORD HEAVY tire traction, box of 12 - #M319

Heavy tire traction. The choice of the Pro's.

Medium tire traction. Ideal for G15 C12 and lower class cars which require a lighter glue

INTERIOR FOR "TEAPOT" 1/24 BODIES

• Made from: Polyvinyl chloride (PVC)
• For: "TEAPOT" 1/24 
• Thickness, mm: 0,2

DUBICK Lead wire retainers, 2 pcs.

Lead wire retainer. Prevents lead wire from dragging on track, solders to middle rail.

JK 3/32" (2.36 mm), .010" (0.254 mm) thick, stainless steel axle spacers, pack of 100 pcs. - #U72-100

JK Gear 64 pitch, 32T, 0° angle, 3/32" axle, 1 cd. (6 pcs.) - #G632-6

Old catalog #JKG632-6

MID AMERICA .003" (0.08 mm) Stainless steel guide spacers, 8 pcs. - #MID147S

WRIGHTWAY Paste flux - #WW10

Paste Flux in plastic syringe

MID AMERICA Soldering paste flux, 15 g., tin - #MID111B

Clear Production 1/32 Peugeot body

• Made from: Polycarbonate (Lexan)
• For: Production 1/32
• Thickness: .005" (0.125 mm)
  • Clear body, with paint mask

KOFORD EDM Drilled Ø2 mm AXLE, selection

EDM drilled, 2mm .040 hole qualifying/race axle. premium plated axles for Eurosport made using ultrahigh strength steel and plated and ground.

CAHOZA EDM drilled (.040" hole) Ø2 mm hollow axle - #24-H

The axle is drilled by EDM, hole diameter is 1.0mm (.04"), axle is very accurate, although the axle is lightened it is still strong

Ballbearing 1.5 х 4 х 1.2 mm  open , 6 balls - 1 Pc.

CAHOZA Light braid, 408 strands, .023" thick, 1 pair - #340

these braids size is 4.5 x 0.6 x 30 mm (.177" x .023" x 1.181"), 408 strands, made from very pure copper (99.9 %), these braids are ideal for PR24, ES24, SP32 and F1/32, they will last longer, the production process is finalized by Cahoza (handmade)

 These are heat treated 80 pitch 6 tooth pinions with a 1.2 mm bore. Certified to RC55

KOLHOZA 1/24 Custom painted car interior, white, thin .005" (0,125 mm) - #0126-white

KOLHOZA 1/24 Custom painted car interior, red, thin .005" (0,125 mm) - #0126-red

KOLHOZA 1/24 Custom painted car interior, green, thin .005" (0,125 mm) - #0126-green

K&S Round brass tube 1/8" x .014" x 12" (3.15 mm x 0.355 mm x 304.8 mm), 1 pack (3 pcs.) - #KS8127

JK Ø3/32" (2.36 mm) rear axle, for Eurosport 1/32, Production 1/32 & other cars in scale 1/32, length 1.968" (50 mm ) - #A9

Old catalog #JK55012

Self centering ultra light aluminum alloy spring cups for Koford set ups

JK Precision guide nut wrench for JK#U61 nut - #L30

.003 phosphor bronze spacers,Ultra precision fit on armature shaft to eliminate vibration due to loose fit, phosphor bronze is very hard but will not stick to magnets, 12 per bag

ANODISED SPRING POSTS - 3 COIL SPRINGS
aluminium anodised spring posts for 3 coil springs, spring post do not fit Cahoza plastic G12 endbells, suitable for hardware #170 and #171, packaged 10 pairs per bag

VITULA Ø3/32" (2.36 mm) rear axle (length 58 mm)

Axles are made of hardened tool steel 60HRC.  Axles have the deflection to the limit of 0.01 mm and the tolerance of the diameter 0.002 mm.

TAMIYA 1/14 R/C Mercedes-Benz Race Truck Actros MP4 MB Motorsport (TT-01 Type-E) - #58683

For more information click here: https://www.tamiya.com/english/products/58683/index.htm 

JK Cheetah AEOLOS 4" Production 1/24 chassis - #C26

Old catalog #C43

ZHB Fiberglass sheet, foil on the one side, thick. 1,5 mm, sheet 100*150 mm

Very high quality fiberglass. It is well spilled with resin and does not separate.

CAHOZA Medium braid, 552 strands, .027" thick, 1 pair - #341

these braids size is 4.8 x 0.7 x 30 mm (.188" x .027" x 1.181"), 552 strands, made from very pure copper (99.9 %), these braids are ideal for PR24 and ES24, they will last longer, the production process is finalized by Cahoza (handmade)

DUBICK SEVEN-DIODES controller w/alligator clips

Variable brake for all motors up to 12 groups (Johnson, Hawk group, 16 & 12 group motors).

MAGNEHONE Hood tool

Diamond coated hood tool, for brush hoods

CAHOZA Heavy braid, 624 strands, .031" thick, 1 pair - #342

these braids size is 5.0 x 0.8 x 30 mm (.196" x .031" x 1.181"), 624 strands, made from very pure copper (99.9 %), these braids are ideal for wing cars, they will last longer, the production process is finalized by Cahoza (handmade)

CAHOZA Heavy braid - #345

• 624 strands,
• Sizes: 5,0 mm x 0,8 mm x 30 mm( .197" x .031" x 1.181"),
• 1 pair

Made from very pure copper (99.9 %), these braids are ideal for wing cars, they will last longer, the production process is finalized by Cahoza (handmade).

It is delivered under the order

BSV Plastic rims

• For 3/32" axle; 
• Width 20 mm;
• Dia. 9.5 mm;
• Ultra light.

BSV Plastic rims

• For 3/32" axle; 
• Width 20 mm;
• Dia. 9.5 mm;
• W/offset of the hub;
• Ultra light.

ZHB Fiberglass sheet, foil on the one side, thick. 1,5 mm, sheet 100*200 mm

Very high quality fiberglass. It is well spilled with resin and does not separate.

CAHOZA Black covered pinion 72 pitch 5 teeth, 0° angle 1.2 mm bore - #17A

EDM pinions 72 pitch 5T - 1,2mm hole, very accurate, plated with special black cover especially developed for Cahoza, this cover enhances lubricity 8 times and repels solder so teeth cannot be soldered through, after application the pinion hole is firmly cut to exact size and solder then sticks perfectly in, made from stainless steel 45 HRc, suitable for all types of gears, ideal for Cahoza 72 pitch gears

Clear Body Formula 1/24 McLaren MCL 35 2020

• Made from: Polycarbonate (Lexan)
• For: Formula 1/24
• Thickness: .007" (0.175 mm)
• Clear body

Clear Body Formula 1/24 Alpine A522 2022

• Made from: Polycarbonate (Lexan)
• For: Formula 1/24
• Thickness: .005" (0.125 mm)
• Clear body

Clear Body Formula 1/24 Alpine A522 2022

• Made from: Polycarbonate (Lexan)
• For: Formula 1/24
• Thickness: .007" (0.175 mm)
• Clear body

BSV Crown gear 48 pitch 27T, 3/32" axle,  Ø17.2 mm - #BSV0727

PROSLOT PRO-SRS Blueprinted C-Can, straightened perfectly

MID AMERICA Guide nut - aluminum pin drive, black - #MID138B

Fits with #MID138 

MID AMERICA Guide nut - aluminum pin drive, black, 1 cd. (6 pcs.) - #MID138B

Fits with #MID138 

MID AMERICA Guide nut - aluminum pin drive, red - #MID138R

Fits with #MID138 

BSV LUXURY Donuts, inside Ø 9.1 mm (.354"), outside about Ø 21 mm (.830"), about 22 mm (.870") width, pair

Good for Production & Eurosport.

Replacement 4/40 allen head set screws for Slot Car Front Wheels, Rear Wheels and Spur Gears. 

JK Front wheel donuts, 0.375"ID (9,52 mm) x 0.850"OD (21,6 mm), firm, pair - #D1F

PARAMETERS

• Inside dia., in (mm): .375 (9,52)
• Outside dia., in (mm): .850 (21,6)

DUBICK Anodized spring cups /3 coil springs

MID AMERICA Guide nut - aluminum pin drive, green, 1 pc - #MID138GR

Fits with #MID138 

MID AMERICA Guide nut - aluminum pin drive, green, 1 cd. (6 pcs.) - #MID138GR

Fits with #MID138 

MID AMERICA Guide nut - aluminum pin drive, orange, 1 pc - #MID138O

Fits with #MID138 

MID AMERICA Guide nut - aluminum pin drive, orange, 1 cd. (6 pcs.) - #MID138O

Fits with #MID138 

MID AMERICA Carbon fiber rims - #MID850-2mm

• For 2 mm; 
• width .810" (20 mm);
• Dia. .370" (9.5 mm);

MID AMERICA Carbon fiber rims - #MID850

• For 3/32" axle; 
• width .810" (20 mm);
• Dia. .370" (9.5 mm);

MID AMERICA Carbon fiber rims, 1 cd. (6 pairs) - #MID850

• For 3/32" axle; 
• width .810" (20 mm);
• Dia. .370" (9.5 mm);

R-GEO Cahoza gear driller - #615

Tool for decrese the total weight of the gear.

See the description on the following photo. 

CHAMPION 1/32 Stock car words, black, 1 pc. - #CHA373A

CHAMPION 1/32 Stock car words, white, 1 pc. - #CHA373B

MID AMERICA Guide nut - aluminum pin drive, pink, 1 pc - #MID138P

Fits with #MID138 

JK bushings in production chassis, pair 

• Outer Diameter: 3/16″ (4.76 mm);
• Inner Diameter: 3/32″ (2.36 mm).
• Old catalog #JK5574

JK bushings in production chassis, 1 cd. (6 pairs)

• Outer Diameter: 3/16″ (4.76 mm);
• Inner Diameter: 3/32″ (2.36 mm).
• Old catalog #JK5574

ZHB Fiberglass sheet, foil on the one side, thick. 1,5 mm, sheet 100*200 mm

Very high quality fiberglass. It is well spilled with resin and does not separate.

JK 4" cheetah Aeolos center section - #C26C

3/32" X 3/16" (2.36 MM X 4.76 MM) AXLE OILITES IN  PRODUCTION CHASSIS, pair

KOFORD 3/32" X 3/16" (2.36 mm X 4.76 mm) axle oilites in production chassis, 1 cd. (6 pairs) - #M546

K&S Tube bender kit - #321

Size range: 1/6" to 3/16" O.D.

Brass, aluminum & copper tubing

DUBICK Precut Brass pin tubes, length 10.8 mm, 4 pcs.- #406

Brass pin tubing for chassis 10.8 mm -4/10 of an inch.

WRIGHT WAY Flux brush, 1 pc.

SLICK7 LEAD WIRE 21Ga (section 0,41 mm²), yellow, 3 m (10 ft), insulation diameter .058" (1,47 mm) - S7-553

Very soft & thin lead wire. 

The best chooise for Formula 1/32!

LEAD WIRE 20Ga (section 0,52 mm²), red, 1 m

Custom Painted Body Production 1/24 Audi RS5 DTM PLAYBOY BUNNY

• • Made from: Polycarbonate (Lexan)
  • For: Production 1/24
  • Thickness: .007" (0.175 mm)
  • Custom Painted Body

Custom Painted Body Production 1/24 Audi RS5 DTM XXX RED BULL

• Made from: Polycarbonate (Lexan)
• For: Production 1/24
• Thickness: .007" (0.175 mm)
• Custom Painted Body

Custom Painted Body Production 1/24 Audi RS5 DTM HOFFMAN GROUP

• Made from: Polycarbonate (Lexan)
• For: Production 1/24
• Thickness: .007" (0.175 mm)
• Custom Painted Body

It is delivered to order in the latest available version at the time of order.

All chassis starting from 2016 will be made of German high-carbon structural steel 1 mm thick. This is the same material that is used the world's leading chassis manufacturers.

Custom Painted Body Production 1/24 Audi RS5 DTM ARAL

• Made from: Polycarbonate (Lexan)
• For: Production 1/24
• Thickness: .007" (0.175 mm)
• Custom Painted Body

PARAMETERS:

• Type: C-arm
• Wingings: 45/29
• Dia.: 0.460"
• Stack: 0.240"
• Long (by ballbearings): 0.660"
• Advance angle: 28
• Arm.shaft: 1,5mm

KOLHOZA Clear body Eurosport 1/32 Audi R15 2008

This body is presented for legalisation by ISRA rules for the next vote!

• Made from: Polycarbonate (Lexan)
• For: Eurosport 1/32
• Thickness: .007" (0.175 mm)
• Clear body.

DUBICK Adjustable DUBICK Fanat PRO controller chip

DUBICK Plastic box 75 х 132 х 16 mm (2.96" x 5.2" x 0.63") w/12 individual boxes

• Material: plastic with transparent cover.
• Dimension, mm (in.): 75 х 132 х 16 mm (2.96" x 5.2" x 0.63").
• Quantity of sections, pcs.: 40.
• Small storage box for parts great for storing pinions etc.

DUBICK Electronic controller FANAT Pro

-suitable for all classes of models;
-antibrake, antibrake correction;
-electronic CHOKE;
-Slow Attach/ fast Attachk function (innovation!!!)
-15 chips;
-built-in voltmeter;
-gold-plated contact block;
-holders for track board;
-Transistor Correction

MID AMERICA Guide nut - aluminum pin drive, pink, 1 cd. (6 pcs.) - #MID138P

Fits with #MID138 

JK 4" cheetah Aeolos 1 piece pan 0.040" thick - #C26PT

MID AMERICA RTR 1/32 stomp car without body - #MID350

Ready to Run car less body. Comes with Brass Stomp chassis and Retro Eagle motor. 1/8 axle and 48 pitch gears.

Clear body ES-G12 Toyota GT ONE GB

• Made from: Polycarbonate (Lexan)
• For: ES-G12
• Thickness: .007" (0.175 mm)
• Clear body w/paint mask.

Clear Body ES G12-24 outlaw Bentley WR

• Made from: Polycarbonate (Lexan)
• For: ES G12-24 outlaw
• Thickness: .005" (0.125 mm)
• Clear body

Clear Body ES G12-24 outlaw Bentley WR

• Made from: Polycarbonate (Lexan)
• For: ES G12-24 outlaw
• Thickness: .007" (0.175 mm)
• Clear body