S&K
-
S&K PLASTIC RIMS 3/32" axles, width 20 mm, Ø10.5 mm, (1,7 grammes/ pair) - #SK10520
S&K PLASTIC RIMS - #SK10520
PARAMETERS
- axle, mm.: 2,36
- width, mm: 20
- dia.,mm: 10.5
- weight per pair, gr/pair: 1,7
-
S&K PLASTIC RIMS FOR 2 mm axle, width 16 mm, Ø10.5 mm, ultra light (1,62 gr/pair)
PARAMETERS
- axle, mm: 2
- width, mm: 16
- dia.,mm: 10,5
- weight per pair, gr/pair: 1,62
-
S&K Crown gear, hypoid 72 pitch 30 teeth, offset 0,5mm, 3/32" axle, Ø13.2 mm, green - S&K#Offset 0.5mm
This gear used in Formula 1/32.
But, when you set this gear you need use special tool (tool for set motor on F1 with down offset 0.5 mm)
-
S&K Crown gear, hypoid 72 pitch 30 teeth , offset 0.5 mm, 2 mm axle, Ø13.2 mm, green - S&K#Offset 0.5mm - #SK30722
S&K Crown gear, hypoid 72 pitch 30 teeth , offset 0.5 mm, 2 mm axle, Ø13.2 mm, green - S&K#Offset 0.5mm - #SK30722R
This gear used in Formula 1/32.
But, when you set this gear you need use special tool (tool for set motor on F1 with down offset 0.5 mm)
-
S&K PINION 80 PITCH, 6T, 0° angle, 1.5 mm bore, EDM (coated by titanium nitride) - #SK680
S&K PINION 80 PITCH, 6T, 0° angle, 1.5 mm bore, EDM (coated by titanium nitride) - #SK680
-
S&K FRONT WHEELS FOR F 1/32, Ø14,5 mm, pair
FRONT WHEELS FOR F 1/32, Ø14,5 mm, pair
Replacement pair of front wheels for formula 1/32 chassis
-
S&K Gear 80 PITCH, 44T, 0° angle, 3/32" axle, Ø14,6 mm - #SK4480
S&K Gear 80 PITCH, 44T, 0° angle, 3/32" axle, Ø14,6 mm - #SK4480
-
S&K PLASTIC RIMS FOR 2 mm axle, width 16 mm, Ø10.5 mm,w/offset of the hub for ES 1/32 & Production 1/32, ultra light(1,64 gr/pair)
PARAMETERS
- axle, mm: 2
- width, mm: 16
- dia.,mm: 10,5
- weight per pair, gr/pair: 1,64
- with offset of hub for ES 1/32 & Production 1/32
-
S&K PLASTIC RIMS FOR 3/32" axle, width 20 mm, Ø11 mm, ultra light (1,82 gr/pair) - #SK1120
S&K PLASTIC RIMS, ultra light (1,82 gr/pair) - #SK1120
PARAMETERS
- axle, mm.: 2,36
- width, mm: 20
- dia.,mm: 11
- weight per pair, gr/pair: 1,82
-
S&K PLASTIC RIMS FOR 2 mm axle, width 20,2 mm, Ø10.5 mm, ultra light (1,72 gr/pair)
PARAMETERS
- axle, mm: 2
- width, mm: 20,2
- dia.,mm: 10,5
- weight per pair, gr/pair: 1,72
-
S&K GEAR 64 PITCH, 38T, 0° angle, 3/32" axle, Ø15.65 mm - #SK3864
S&K GEAR 64 PITCH, 38T, 0° angle, 3/32" axle, Ø15.65 mm - #SK3864
-
S&K GEAR 64 PITCH, 37T, 16° angle, 3/32" axle, Ø15.47 mm - #SK3764A
S&K GEAR 64 PITCH, 37T, 16° angle, 3/32" axle, Ø15.47 mm - #SK3764A
-
S&K GEAR 72 PITCH, 42T, 0° angle, 3/32" axle, Ø15.46 mm - #SK4272
S&K GEAR 72 PITCH, 42T, 0° angle, 3/32" axle, Ø15.46 mm - #SK4272
-
S&K Gear 80 PITCH, 45T, 0° angle, 2 mm axle, Ø14,9 mm - #SK45802
S&K Gear 80 PITCH, 45T, 0° angle, 2 mm axle, Ø14,9 mm - #SK45802
-
S&K Crown gear 72 pitch 33 teeth, offset 0.5 mm, 2 mm axle, Ø13.2 mm, green - #SK3372
S&K Crown gear 72 pitch 33 teeth, offset 0.5 mm, 2 mm axle, Ø13.2 mm, green - #SK3372R
This gear used in Formula 1/32
-
S&K Gear 80 PITCH, 45T, 0° angle, 3/32" axle, Ø14,9 mm - #SK4580
S&K Gear 80 PITCH, 45T, 0° angle, 3/32" axle, Ø14,9 mm - #SK4580
-
S&K Gear 72 pitch 44 teeth, 16° angle, 3/32" axle, Ø15.8 mm - #SK4472A
S&K Gear 72 pitch 44 teeth, 16° angle, 3/32" axle, Ø15.8 mm - #SK4472A
-
S&K Gear 80 PITCH, 45T, 0° angle, 3/32" axle, Ø14,9 mm, for gluing - #SK4580G
S&K Gear 80 PITCH, 45T, 0° angle, 3/32" axle, Ø14,9 mm, for gluing - #SK4580G
-
S&K GEAR 64 PITCH, 39T, 0° angle, 3/32" axle, Ø16.02 mm - #SK3964
S&K GEAR 64 PITCH, 39T, 0° angle, 3/32" axle, Ø16.02 mm - #SK3964
-
S&K Crown gear, hypoid 72 pitch 33 teeth, offset 0,5mm, 3/32" axle, Ø13.2 mm, green - S&K#
This gear used in Formula 1/32.
But, when you set this gear you need use special tool (tool for set motor on F1 with down offset 0.5 mm)
-
S&K PINION 72 PITCH, 7T, 0° angle, EDM, 2 mm bore (coated by titanium nitride) - #SK772
S&K PINION 72 PITCH, 7T, 0° angle, EDM, 2 mm bore (coated by titanium nitride) - #SK772
-
S&K Power supply leads 16Ga (section 1,31 mm²), "banana" clips from one side/ "alligator" clips from other, 0,8 m - #0109
S&K Power supply leads 16Ga (section 1,31 mm²) w/clips, 0,8 m - #0109
16 gauge wire with small 4 mm banana plugs and alligator clips, 0,8 m long - same as that comes with their power supply.
-
S&K F1 motor adjustment tool for offset crowns with 2 mm axle - #0104
CONDUCTOR FOR SET THE MOTOR ON F1, WITH THE CENTER SHIFTED DOWN BY 0,5 MM, motor shaft 1,5 mm, rear axle 2 mm
Convenient tool for accurate and fast installation of the motor on F1: fixes the center of the motor shaft and the axis, after which the motor is soldered.
-
S&K F1 motor adjustment tool for offset crowns with 3/32" axle - #0103
CONDUCTOR FOR SET THE MOTOR ON F1, WITH THE CENTER SHIFTED DOWN BY 0,5 MM, motor shaft 1,5 mm, rear axle 3/32"
Convenient tool for accurate and fast installation of the motor on F1: fixes the center of the motor shaft and the axis, after which the motor is soldered.