DUBICK Engineering
-
DUBICK Reinforcement tape for pin hole, 30 x 180 mm (1,18" x 7,1") - #707
DUBICK Reinforcement tape for pin hole, 30 x 180 mm (1,18" x 7,1") - #707
-
DUBICK gold plated short guide clips. Made special for new RED FOX guides. (But also fit for all other guides), 1 pair - #701
DUBICK gold plated short guide clips. Made special for new RED FOX guides. (But also fit for all other guides), 1 pair (NEW!)
-
DUBICK Lead sheet thickness 0.5 mm, 50 х 50 mm (.019", 1.968" x 1.968") with a 3M selfstick adhesive tape - #209
DUBICK Lead sheet thickness 0.5 mm, 50 х 50 mm (.019", 1.968" x 1.968") with a 3M selfstick adhesive tape - #209
Lead sheet thickness 0.5 mm, 50 х 50 mm with a adhesive tape can help you to configure your chassis.
The presence of stick layer eliminates the need for glue application and simplifies the work! -
DUBICK gold plated long guide clips. Made special for new RED FOX guides. (But also fit for all other guides), 1 pair - #702
DUBICK gold plated long guide clips. Made special for new RED FOX guides. (But also fit for all other guides), 1 pair
-
DUBICK 61/39 QUALITY SOLDER in storage tube, diameter 1mm, long 6 feet (1.8 m), 1 pc. - #211
DUBICK 61/39 QUALITY SOLDER in storage tube, diameter 1mm, long 6 feet (1.8 m), 1 pc. - #211
-
DUBICK Tire truer
DUBICK Tire truer
New tire truer with on / off button, made with two types of needle trimming in diameter, three spacers 16 mm, 20 mm, 20.7 mm, a limb for setting the diameter as on a micrometer, a reduced size and weight. Comes with a storage bag.
-
DUBICK gold plated guide clips with crimping for wires. Made for new RED FOX guides.(Fit for all other guides), 1 pair - #703
DUBICK gold plated guide clips with crimping for wires. Made for new RED FOX guides.(Fit for all other guides), 1 pair
-
DUBICK 2026 ES 1/32 Eurosport chassis assembled w/out ballbearings, for brushless motor - #322026
DUBICK 2026 ES 1/32 Eurosport chassis assembled w/out ballbearings, for brushless motor - #322026
All chassis starting from 2016 will be made of German high-carbon structural steel 1 mm thick. This is the same material that is used the world's leading chassis manufacturers.
-
DUBICK Lead wire retainers, 2 pcs. - #710
DUBICK Lead wire retainers, 2 pcs.
-
DUBICK SEVEN-DIODES controller w/alligator clips - #727-7AC
DUBICK SEVEN-DIODES controller w/alligator clips
Variable brake for all motors up to 12 groups (Johnson, Hawk group, 16 & 12 group motors).
-
DUBICK Anodized spring cups / 3 coil springs - #716
DUBICK Anodized spring cups /3 coil springs
-
DUBICK Precut Brass pin tubes, length 10.8 mm, 4 pcs.- #406
DUBICK Precut Brass pin tubes, length 10.8 mm, 4 pcs.- #406
Brass pin tubing for chassis 10.8 mm -4/10 of an inch.
-
DUBICK Engineering 2020 Open 12 chassis assembled without ballbearings - #122020
All chassis starting from 2016 will be made of German high-carbon structural steel 1 mm thick. This is the same material that is used the world's leading chassis manufacturers.
-
DUBICK Adjustable DUBICK Fanat PRO controller chip
DUBICK Adjustable DUBICK Fanat PRO controller chip
-
DUBICK Plastic box 75 х 132 х 16 mm (2.96" x 5.2" x 0.63") w/12 individual boxes - #214
DUBICK Plastic box 75 х 132 х 16 mm (2.96" x 5.2" x 0.63") w/12 individual boxes
- Material: plastic with transparent cover.
- Dimension, mm (in.): 75 х 132 х 16 mm (2.96" x 5.2" x 0.63").
- Quantity of sections, pcs.: 40.
- Small storage box for parts great for storing pinions etc.
-
DUBICK Electronic controller FANAT Pro
DUBICK Electronic controller FANAT Pro
-suitable for all classes of models;
-antibrake, antibrake correction;
-electronic CHOKE;
-Slow Attach/ fast Attachk function (innovation!!!)
-15 chips;
-built-in voltmeter;
-gold-plated contact block;
-holders for track board;
-Transistor Correction -
DUBICK Controller chip 29 Ohm for DUBICK Electronic controller - #722-29
DUBICK Controller chip 29 Ohm for DUBICK Electronic controller
-
DUBICK Controller chip 58 Ohm for DUBICK Electronic controller - #722-58
DUBICK Controller chip 58 Ohm for DUBICK Electronic controller
-
DUBICK Anodized spring cups / 5 coil springs - #717
DUBICK Anodized spring cups / 5 coil springs
-
DUBICK Electronic controller Pro version
DUBICK Electronic controller Pro version
- -suitable for all classes of models;
- -more functional than S&K, Kobis or DiFalco controllers;
- -antibrake, antibrake correction;
- -wire CHOKE;
-traction control;
- -one or two transistors in use;
- -adjust the sharpness of the transistor;
- -15 chips;
- -built-in voltmeter;
- -gold-plated contact block;
- -full protection against incorrect switching on.
-
DUBICK .004" (0.1 mm) Precision steel guide spacers, 6 pcs. - #708
DUBICK .004" (0.1 mm) Precision steel guide spacers, 6 pcs.
-
DUBICK Pinion gear 48 pitch, 6T, 2 mm bore, brass (This is solder style pinion gear) - #501-6
48 pitch Straight stainless steel 6 tooth pinion gears
IN STOCK!
-
DUBICK Precut Brass pin tubes, length 10.8 mm, storage tube (24 pcs.) - #407
DUBICK Precut Brass pin tubes, length 10.8 mm, storage tube (24 pcs.) - #407
Brass pin tubing for chassis 10.8 mm -4/10 of an inch
-
DUBICK Diamond hone for increase inside tire diameter till 10,5 mm (0,413")
DUBICK Diamond hone for increase inside tire diameter till 10,5 mm (0,413")
-
DUBICK Plastic box 104 х 175 х 22 mm (4.09" x 6.89" x 0.87") w/15 configurable sections - #215
DUBICK Plastic box 104 х 175 х 22 mm (4.09" x 6.89" x 0.87") w/15 configurable sections - #215
- Material: plastic with transparent cover.
- Dimension, mm (in.): 104 х 175 х 22 mm (4.09" x 6.89" x 0.87").
- Quantity of configurable sections, pcs.: 15.
- Plastic parts box like the DE214 but bigger
-
DUBICK Pinion gear 48 pitch, 7T, 2 mm bore, brass (This is solder style pinion gear) - #501-7
48 pitch Straight stainless steel 7 tooth pinion gears
IN STOCK!
-
DUBICK Lead sheet thickness 1 mm, 50 х 50 mm (.039", 1.968" x 1.968") with a 3M selfstick adhesive tape - #210
DUBICK Lead sheet thickness 1 mm, 50 х 50 mm (.039", 1.968" x 1.968") with a 3M selfstick adhesive tape - #210
Lead sheet thickness 1 mm, 50 х 50 mm with a adhesive tape can help you to configure your chassis.
The presence of stick layer eliminates the need for glue application and simplifies the work! -
DUBICK Controller chip 78 Ohm for DUBICK Electronic controller - #722-78
DUBICK Controller chip 78 Ohm for DUBICK Electronic controller
-
DUBICK Lexan (polycarbonate) for body reinforcement, w/sticky layer 3M, thickness .005" (0.125 mm), size 1.968" x 6.692" (50x170 mm) - #2070
Lexan for body reinforcement
Parameters
- Thickness: .005" (0.125 mm)
- Size: 1.968" x 6.692" (50x170 mm)
- w/sticky layer 3M
-
DUBICK Desktop organizer for working with small parts 3" x 4 1/2" x .4" (76,2 × 115 × 10 mm). Has a built-in magnet - #704
DUBICK Desktop organizer for working with small parts 3" x 4 1/2" x .4" (76,2 × 115 × 10 mm). Has a built-in magnet - #704
-
DUBICK Controller chip 95 Ohm for DUBICK Electronic controller - #722-95
DUBICK Controller chip 95 Ohm for DUBICK Electronic controller
-
DUBICK Controller chip 113 Ohm for DUBICK Electronic controller - #722-113
DUBICK Controller chip 113 Ohm for DUBICK Electronic controller
-
DUBICK Controller chip 144 Ohm for DUBICK Electronic controller - #722-144
DUBICK Controller chip 144 Ohm for DUBICK Electronic controller
-
DUBICK Controller chip 194 Ohm for DUBICK Electronic controller - #722-194
DUBICK Controller chip 194 Ohm for DUBICK Electronic controller
-
DUBICK Controller chip 238 Ohm for DUBICK Electronic controller - #722-238
DUBICK Controller chip 238 Ohm for DUBICK Electronic controller
-
DUBICK Controller chip 290 Ohm for DUBICK Electronic controller - #722-290
DUBICK Controller chip 290 Ohm for DUBICK Electronic controller
-
DUBICK Controller chip 319 Ohm for DUBICK Electronic controller - #722-319
DUBICK Controller chip 319 Ohm for DUBICK Electronic controller
-
DUBICK Controller chip 348 Ohm for DUBICK Electronic controller - #722-348
DUBICK Controller chip 348 Ohm for DUBICK Electronic controller
-
DUBICK Controller chip 377 Ohm for DUBICK Electronic controller - #722-377
DUBICK Controller chip 377 Ohm for DUBICK Electronic controller
-
DUBICK Controller chip (custom resistance) for DUBICK Electronic controller
DUBICK Controller chip (custom resistance) for DUBICK Electronic controller
-
DUBICK 4/40" x 1/8" set screws, 1 tube (12 pcs.) - #399
DUBICK 4/40" x 1/8" set screws, 1 tube (12 pcs.) - #399
Tire and gear size.
-
DUBICK 4/40" x 1/8" set screws, bulk pack of 25 pcs. - #400
DUBICK 4/40" x 1/8" set screws, bulk pack of 25 pcs. - #400
Tire and gear size.
-
DUBICK Diamond hone for increase inside tire diameter till 11 mm (0,433")
DUBICK Diamond hone for increase inside tire diameter till 11 mm (0,433")
-
DUBICK Precut Brass pin tubes, length 11.8 mm (.464"), 4 pcs. - #4081
DUBICK Precut Brass pin tubes, length 11.8 mm (.464"), 4 pcs. - #4081
-
DUBICK Tweezers stainless steel, non-magnetic - #715
DUBICK Tweezers stainless steel, non-magnetic - #715
Perfect for work with small parts!
-
DUBICK TECH BLOCK WITH MAGNETS - #205
DUBICK TECH BLOCK WITH MAGNETS - #205
Textolite tech block for models with fixed samarium-cobalt magnets. It is made with a cut zone of guide and rear wheels. Has an even working plane.
-
DUBICK Holder for the armatures & armatures in the tubes
DUBICK Holder for the armatures & armatures in the tubes
-
DUBICK Traditional flat controller trigger - #726
DUBICK Traditional flat controller trigger - #DB726
Same as Parma finger trigger profile. Suitable for Parma, DiFalco or JK controllers. Has an additional brass tube for spring-loaded moving contact.
-
DUBICK 4/40" x 1/8" set screws, tube (50 pcs.) - #401
DUBICK 4/40" x 1/8" set screws, tube (50 pcs.) - #401
Tire and gear size.
-
DUBICK VISCOSE SPONGE FOR CLEANING SOLDERING IRON TIP, 42 х 54 х 6 mm (1.65" x 2.13" x 0.24") - #212
DUBICK VISCOSE SPONGE FOR CLEANING SOLDERING IRON TIP, 42 х 54 х 6 mm (1.65" x 2.13" x 0.24") - #212
Viscose sponge for cleaning soldering iron tip
-
DUBICK Blue viscose sponge for cleaning soldering iron tip, 65 х 65 х 7 mm (2.55" x 2.55" x 0.28") - #2121
DUBICK Blue viscose sponge for cleaning soldering iron tip, 65 х 65 х 7 mm (2.55" x 2.55" x 0.28") - #2121
-
DUBICK PINION GEAR 48 PITCH, 8T, 2 mm bore, BRASS (This is press-on style pinion gear) - #501-8
DUBICK PINION GEAR 48 PITCH, 8T, 2 mm bore, BRASS
This is press-on style pinion gear
-
DUBICK 4/40" x 1/8" set screws, tube (100 pcs.) - #402
DUBICK 4/40" x 1/8" set screws, tube (100 pcs.) - #402
Tire and gear size.
-
DUBICK Set of contacts for the controller. Made from brass and GOLD PLATED - #714
DUBICK set of contacts for the controller. Made from brass and GOLD PLATED.
Fit for Parma, Jk and RedFox controller triggers. Full analog Parma #355D TURBO CONTACTS & TERMINALS and fit for Parma turbo controller frame.
-
DUBICK .01" (0.25 mm) Precision steel guide spacers, 6 pcs. - #709
DUBICK .01" (0.25 mm) Precision steel guide spacers, 6 pcs.
-
DUBICK Precut Brass pin tubes, length 11.8 mm (.464"), storage tube (24 pcs.) - #409
DUBICK Precut Brass pin tubes, length 11.8 mm (.464"), storage tube (24 pcs.) - #409
-
DUBICK LEXAN (POLYCARBONATE) FOR BODY REINFORCEMENT, W/STICKY LAYER 3M, thickness .005" (0.125 mm), size 1.968" x 9.449" (50 x 240 mm) - #2070
Lexan for body reinforcement
Parameters
- Thickness: .005" (0.125 mm)
- Size: 1.968" x 9.449" (50 x 240 mm)
- w/3M sticky layer
-
DUBICK TECH BLOCK WITHOUT MAGNETS - #2051
DUBICK TECH BLOCK WITHOUT MAGNETS - #2051
-
DUBICK Engineering 2026 F1-32 chassis assembled without ballbearings, for brushless motor - #F12026
DUBICK Engineering 2026 F1-32 chassis assembled without ballbearings, for brushless motor - #F12026
All chassis starting from 2016 will be made of German high-carbon structural steel 1 mm thick. This is the same material that is used the world's leading chassis manufacturers.
The chassis comes with a front wheels
-
DUBICK 0- 15V, 17A Power Supply. 110V or 220V. Weight 750 gr. Dimensions: 122 x 70 x 208 mm.
We are happy present our new Power Supply!
It is two power supply in one!
- In the kit there is an additional block adapter on 10 Volts and 10 Amperes, for simultaneous work with several engines or tools
- ability to accurately adjust the current and voltage.
- The range of voltage adjustment is from 0 to 15 Volts and current from 0 to 17 Amps.
- Accuracy of adjustment to 0.01 both voltage and current.
- Ability to work from 110 and 220 Volts.
- The unit can be controlled via Bluetooth.
- There is also a USB Charger with a maximum current of up to 3 Amps.
- Connection of a soldering iron is possible (possible order extra solder iron like on picture)
- Crocodile wires are included.
- The weight of the entire set of 960 grams.
- Dimensions: 122 x 70 x 208 mm. -
DUBICK DIAMOND COMMUTATOR CUTTING TOOL for arms with cup - #213
DUBICK DIAMOND COMMUTATOR CUTTING TOOL for arms with cup - #213
-
DUBICK Egineering Power supply with the ability to accurately adjust the amperage (0-12 A) and voltage (0-15 V). Input voltage 220V/110V. Dimensions: 4.803" x 2.756" x 8.189" (122 x 70 x 208 mm)
DUBICK Egineering Power supply with the ability to accurately adjust the amperage (0-12 A) and voltage (0-15 V). Input voltage 220V/110V. Dimensions: 4.803" x 2.756" x 8.189" (122 x 70 x 208 mm)
The range of voltage regulating from 0 to 15 Volts and amperage from 0 to 12 Amperes.
The adjustment accuracy is up to 0.01 both voltage and amperage.
Ability to work from 110 and 220 volts.
USB Charger.
Wires are attached.
Weight 850 Grams.
Dimensions: 4.803" x 2.756" x 8.189" (122 x 70 x 208 mm)
-
DUBICK 3 coil motor springs, steel, pair - #600
DUBICK 3 coil motor springs, steel, pair - #600
3 coil springs for group 12 and higher motors. Made from hardened steel - one pair
-
DUBICK Duralumin guide nut metric thread for JK style 3 hole wrench - #784
DUBICK Duralumin guide nut metric thread for JK style 3 hole wrench - #784
-
DUBICK Rear bridge for the chassis "TEAPOT" 1/24 (model width 83 mm, rims width 18 mm, brigde width 43.5 mm)
DUBICK Rear bridge for the chassis "TEAPOT" 1/24 (model width 83 mm, rims width 18 mm, brigde width 43.5 mm)
Suitable for 16 mm gears.
-
DUBICK Duralumin guide nut metric thread for 9 mm (.354") wrench, 0.3 grams weight - #769
DUBICK Duralumin guide nut metric thread for 9 mm (.354") wrench, 0.3 grams weight - #769
-
DUBICK diamond drum for tire truer BSV, 70 grit (grain diameter 0,315 mm) - #718
DUBICK Diamond drum for tire truer BSV, grain 0,3/0 mm
-
DUBICK Diamond drum for HUDY tire truer, 60 grit (grain diametr 0,250 mm) - #751
DUBICK Diamond drum for HUDY tire truer, 60 grit (grain diametr 0,250 mm) - #751
-
DUBICK LEXAN (POLYCARBONATE) FOR BODY REINFORCEMENT, w/3M sticky layer, thickness .007" (0.175 mm), size 1.968" x 7.087" (50 x 180 mm) - #2071
Lexan for body reinforcement
Parameters
- Thickness: .007" (0.175 mm)
- Size: 1.968" x 7.087" (50 x 180 mm)
- w/3M sticky layer
-
DUBICK Ballbearing 2 х 5 х 2,3 mm flanged, shielded, 7 balls, pair - #608
DUBICK Ballbearing 2 х 5 х 2,3 mm flanged, shielded, 7 balls, pair - #608
-
DUBICK Pinion 64 pitch, 9T , 0° angle, 2 mm bore, brass (This is press-on style pinion gear) - #502-9
Pinion 64 pitch, 9T , 0° angle, 2 mm bore, brass
This is press-on style pinion gear
-
DUBICK Precision Ballbearing 2 х 5 х 2.3 mm, flanged, shielded - #607
DUBICK Precision Ballbearing 2 х 5 х 2.3 mm, flanged, shielded - #607
-
DUBICK Rear bridge for the chassis "SUPER-TEAPOT" 1/24 (w/hole to the motor)
DUBICK Rear bridge for the chassis "SUPER-TEAPOT" 1/24 (w/hole to the motor)
-
DUBICK Universal kit for assembling body mounting unit of the "Teapot 1/32" & "Teapot 1/24" models. Includes 4 pre-cut tubes. Suitable for JK clips #9008 or #9010
DUBICK Universal kit for assembling body mounting unit of the "Teapot 1/32" & "Teapot 1/24" models. Includes 4 pre-cut tubes. Suitable for JK clips #9008 or #9010
-
DUBICK Kit for assembly mini-slot car box "Sportsman Working Place" for childrens
DUBICK Kit for assembly mini-slot car box "Sportsman Working Place" for childrens
Parameters:
- Length, mm: 350 (+/- 10-20 mm);
- Width, mm: 210 (+/- 10-20 mm);
- Height, mm: 200 (+/- 10-20 mm);
- + handle for carrying.
-
DUBICK Pinion 64 pitch, 10T , 0° angle, 2 mm bore, brass (This is press-on style pinion gear) - #502-10
Pinion 64 pitch, 10T , 0° angle, 2 mm bore, brass
This is press-on style pinion gear!
-
DUBICK LEXAN (POLYCARBONATE) FOR BODY REINFORCEMENT, w/3M sticky layer, thickness .010" (0.25 mm), size 1.968" x 7.087" (50 x 180 mm) - #2072
Lexan for body reinforcement
Parameters
- Thickness: .010" (0.25 mm)
- Size: 1.968" x 7.087" (50 x 180 mm)
- w/3M sticky layer
-
DUBICK Diamond tire file (w/big & small grain of diamond) - #767
DUBICK Diamond tire file (w/big & small grain of diamond) - #767
-
DUBUCK Precision Ballbearing 2 х 5 х 2.5 mm, unshielded - #605
Ballbearing 2 х 5 х 2.5 mm, unflanged - #605
-
DUBICK PINION GEAR 48 PITCH, 9T, 2 mm bore, BRASS (This is press-on style pinion gear) - #501-9
DUBICK PINION GEAR 48 PITCH, 9T, 2 mm bore, BRASS
This is press-on style pinion gear
-
DUBICK Precision Ballbearing 2 х 6 х 2,3 mm, unflanged - #606
DUBICK Precision Ballbearing 2 х 6 х 2,3 mm, unflanged - #606
-
DUBICK PINION GEAR 48 PITCH, 10T, 2 mm bore, BRASS (This is press-on style pinion gear) - #501-10
DUBICK PINION GEAR 48 PITCH, 10T, 2 mm bore, BRASS
This is press-on style pinion gear
-
DUBICK Front wheels for F1/32 chassis, Ø14,5 mm, pair
DUBICK Front wheels for F1/32 chassis, Ø14,5 mm, pair
Full S&K and Horky analogue. Super strong front wheels.
-
Dubick Diamond brush radius tool dia. 188" (4.77 mm) - #768-188
Dubick Diamond brush radius tool dia. 188" (4.77 mm) - #768-188
-
Dubick Diamond brush radius tool dia. 193" (4.90 mm) - #768-193
Dubick Diamond brush radius tool dia. 193" (4.90 mm) - #768-193
-
Dubick Diamond brush radius tool dia. 197" (5.00 mm) - #768-197
Dubick Diamond brush radius tool dia. 197" (5.00 mm) - #768-197
-
Dubick Diamond brush radius tool dia. 202" (5.13 mm) - #768-202
Dubick Diamond brush radius tool dia. 202" (5.13 mm) - #768-202
-
Dubick Diamond brush radius tool dia. 207" (5.25 mm) - #768-207
Dubick Diamond brush radius tool dia. 207" (5.25 mm) - #768-207
-
Dubick Diamond brush radius tool dia. 211" (5.36 mm) - #768-211
Dubick Diamond brush radius tool dia. 211" (5.36 mm) - #768-211
-
DUBICK SET OF STEEL PROBES FOR MEASUREMENT OF CLEARANCE, 20 pcs from 0,05 to 1 mm - #206
Thickness in set: - 0,05 mm/ 0,1 mm/ 0,15 mm/ 0,2 mm/ 0,25 mm/ 0,3 mm/ 0,35 mm/ 0,4 mm/ 0,45 mm/ 0,5 mm/ 0,55 mm/ 0,6 mm/ 0,65 mm/ 0,7 mm/ 0,75 mm/ 0,8 mm/ 0,85 mm/ 0,9 mm/ 0,95 mm/ 1 mm, respectively
The set is more than enough for the most detailed measurement of clearance!
-
DUBICK GT12 CHASSIS EDM ASSEMBLED - #GT122016
Legal in USA since 2017
-
DUBICK Controller spring - #724
DUBICK Controller spring - #724
-
DUBICK AXLE Ballbearing 3/32" х 3/16" х 3/32" (2.36 х 4.76 х 2.36 mm) flanged shielded, 7 balls, pair - #609
DUBICK AXLE Ballbearing 3/32" х 3/16" х 3/32" (2.36 х 4.76 х 2.36 mm) flanged shielded, 7 balls, pair - #609
Flanged ballbearings for rear bridge
-
DUBICK UHU CONTACT GLUE Schuh&Leder FOR TIRES, flacon 33 ml - #700
Excellent glue for tires, better than the "moment" and "88".
-
DUBICK 2 mm, .04" (1 mm) thick aluminium axle spacer, 1 pc. - #713-1
DUBICK 2 mm, .04" (1 mm) thick aluminium axle spacer, 1 pc. - #713-1
-
DUBICK 2 mm, .059" (1,5 mm) thick aluminium axle spacer, 1 pc. - #713-1.5
DUBICK 2 mm, .059" (1,5 mm) thick aluminium axle spacer, 1 pc. - #713-1.5
-
DUBICK 3M reinforced strapping tape, linear reinforcement, 12 mm x 50 m
DUBICK 3M reinforced strapping tape, linear reinforcement, 12 mm x 50 m
The original American 3M. Reinforced with nylon tape. The best material for reinforcing and repairing polycarbonate and plastic models bodies.
-
DUBICK 3M REINFORCED STRAPPING TAPE, .472" x 1968.5" (12 mm x 50 m) - #2073
DUBICK 3M REINFORCED STRAPPING TAPE, .472" x 1968.5" (12 mm x 50 m) - #2073
The original American 3M. Reinforced with nylon tape. The best material for reinforcing and repairing polycarbonate and plastic models bodies.
-
DUBICK 2 mm, .079" (2 mm) thick aluminium axle spacer, 1 pc. - #713-2
DUBICK 2 mm, .079" (2 mm) thick aluminium axle spacer, 1 pc. - #713-2
-
DUBICK 2 mm, .098" (2,5 mm) thick aluminium axle spacer, 1 pc. - #713-2.5
DUBICK 2 mm, .098" (2,5 mm) thick aluminium axle spacer, 1 pc. - #713-2.5
-
DUBICK Set #2 of 2 mm inside diameter aluminium tubes (1 mm (.04"), 1.5 mm (.059"), 2 mm (.079"), 2.5 mm (.098")) - #713
DUBICK Set #2 of 2 mm inside diameter aluminium tubes (1 mm (.04"), 1.5 mm (.059"), 2 mm (.079"), 2.5 mm (.098")) - #713
In set 2 pc of each size: 1 mm (.04"), 1.5 mm (.059"), 2 mm (.079"), 2.5 mm (.098").
-
DUBICK Power supply leads 16Ga (section 1,31 mm²), "banana" clips from one side/ "alligator" clips from other
DUBICK Power supply leads 16Ga (section 1,31 mm²), "banana" clips from one side/ "alligator" clips from other
-
DUBICK Magnetaizer for slot car motors
DUBICK Magnetaizer for slot car motors
The magnetizer is designed to restore the operability of electric motors with stators on ferrite magnets by means of their pulsed magnetization in the inductor of the device. The magnetizing current in the inductor coil is created by the capacitor bank of the device, which is charged from the AC network with a voltage of 220 or 110 V with a frequency of 50 or 60 Hz.
-
DUBICK STAND FOR STORAGE WHEELS BOTTLES Ø23.5 mm (JK, Alpha), 88 х 117 mm, acrylic- #203-23
DUBICK STAND FOR STORAGE WHEELS BOTTLES Ø23.5 mm (JK, Alpha), 88 х 117 mm, acrylic- #DB203-23
PARAMETERS
- Dia. of wheels bottles, mm: 23,5 (JK, Alpha)
- Quantity of holes for bottles, pcs: 12
- Size, mm: 88x17
- Material: acrylic
-
DUBICK PINION 48 PITCH, 11T, 0° angle 2 mm bore, BRASS (This is press-on style pinion gear) - #501-11
DUBICK PINION 48 PITCH, 11T, 0° angle 2 mm bore, BRASS
This is press-on style pinion gear
-
DUBICK STAND FOR STORAGE WHEELS BOTTLES Ø27 mm (PSE, Alpha Large), 103 x 137 mm, acrylic - #203-27
DUBICK STAND FOR STORAGE WHEELS BOTTLES Ø27 mm (PSE, Alpha Large), 103 x 137 mm, acrylic - #DB203-27
PARAMETERS
- Dia. of wheels bottles, mm: 27 (PSE, Alpha Large)
- Quantity of holes for bottles, pcs: 12
- Size, mm: 103x137
- Material: acrylic
-
DUBICK Diamond motor brush tool (for shunting) - #766
DUBICK Diamond motor brush tool (for shunting) - #766
-
DUBICK MG TOOL FOR PREPARING MOTOR BRUSHES W/DIAMOND WHEEL- #201
A tool that every modelist needs! With it's help quickly and accurately prepare motor brushes for any motors! Comes with a diamond wheel
Tool for motor brushes (horizontal or vertical). A more advanced design of the turtle. includes anodised knurled grip and diamond coated brush radius tool diameter 5,2 mm (.208")
-
DUBICK Luxury carbon series tire bottle stand, for JK tubes 23.5 mm - #203-23-CARBON
DUBICK Luxury carbon series tire bottle stand, for JK tubes 23.5 mm
Box has 12 places for wheels tubes.
-
DUBICK F1 motor adjustment tool for crowns gears with 2 mm axle, 1.5 mm motor shaft and 0.2 mm offset - #711
DUBICK F1 motor adjustment tool for crowns gears with 2 mm axle, 1.5 mm motor shaft and 0.2 mm offset - #711
Special for 5 and 6 teeth 72 pitch pinions. 0.2 mm offset allow instal down F1 motor for more low center of gravity, but not so dangerous like 0.5 mm offset.
-
DUBICK Engineering F1 motor adjustment tool for crowns gears with 3/32" (2.36 mm) axle, 1.5 mm motor shaft and 0.2 mm offset
DUBICK Engineering F1 motor adjustment tool for crowns gears with 3/32" (2.36 mm) axle, 1.5 mm motor shaft and 0.2 mm offset
Special for 5 and 6 teeth 72 pitch pinions. 0.2 mm offset allow instal down F1 motor for more low center of gravity, but not so dangerous like 0.5 mm offset.
-
Dubick Egineering Power supply with the ability to accurately adjust the amperage (0-12A) and voltage (0-15V). Input voltage 220V/110V. Dimensions: 4.803" x 2.756" x 8.189" (122 x 70 x 208 mm)
Dubick Egineering Power supply with the ability to accurately adjust the amperage (0-12A) and voltage (0-15V). Input voltage 220V/110V. Dimensions: 4.803" x 2.756" x 8.189" (122 x 70 x 208 mm)
The range of voltage regulating from 0 to 15 Volts and amperage from 0 to 12 Amperes.
The adjustment accuracy is up to 0.01 both voltage and amperage.
Ability to work from 110 and 220 volts.
USB Charger. Wires are attached.
Weight 850 Grams.
Dimensions: 4.803" x 2.756" x 8.189" (122 x 70 x 208 mm)
-
DUBICK 3M REINFORCED STRAPPING TAPE, .984" x 1968.5" (25 mm x 50 m) - #2074
DUBICK 3M REINFORCED STRAPPING TAPE, .984" x 1968.5" (25 mm x 50 m) - #2074
The original American 3M. Reinforced with nylon tape. The best material for reinforcing and repairing polycarbonate and plastic models bodies.
-
DUBICK 3M REINFORCED STRAPPING TAPE, 1.968" x 1968.5" (50 mm x 50 m) - #2075
DUBICK 3M REINFORCED STRAPPING TAPE, 1.968" x 1968.5" (50 mm x 50 m) - #2075
The original American 3M. Reinforced with nylon tape. The best material for reinforcing and repairing polycarbonate and plastic models bodies.
-
DUBICK Luxury carbon series tire bottle stand, for big Parma tubes 27.5 mm - #203-27-CARBON
DUBICK Luxury carbon series tire bottle stand, for big Parma tubes 27.5 mm
Box has 12 places for wheels tubes.
-
DUBICK Axle ballbearing 1/8" x 1/4" (3.15 mm x 6.35 mm), sheilded, flanged, pair - #719
DUBICK Axle ballbearing 1/8" x 1/4" (3.15 mm x 6.35 mm), sheilded, flanged, pair - #719
-
DUBICK Engineering 2026 ES 1/24 Eurosport chassis assembled without ballbearings, for brushless motor - #242026
DUBICK Engineering 2026 ES 1/24 Eurosport chassis assembled without ballbearings, for brushless motor - #242026
All chassis starting from 2016 will be made of German high-carbon structural steel 1 mm thick. This is the same material that is used the world's leading chassis manufacturers.
-
DUBICK PINION 48 PITCH, 12T, 0° angle 2 mm bore, BRASS (This is press-on style pinion gear) - #501-12
DUBICK PINION 48 PITCH, 12T, 0° angle 2 mm bore, BRASS
This is press-on style pinion gear
-
DUBICK PINION 48 PITCH, 13T, 0° angle 2 mm bore, BRASS (This is press-on style pinion gear) - #501-13
DUBICK PINION 48 PITCH, 13T, 0° angle 2 mm bore, BRASS
This is press-on style pinion gear
-
DUBICK PINION 48 PITCH, 14T, 0° angle, 3 mm bore, BRASS (This is press-on style pinion gear) - #501-14
DUBICK PINION 48 PITCH, 14T, 0° angle, 3 mm bore, BRASS
This is press-on style pinion gear
-
DUBICK PINION 48 PITCH, 15T, 0° angle, BRASS (This is press-on style pinion gear) - #501-15
DUBICK PINION 48 PITCH, 15T, 0° angle, BRASS (This is press-on style pinion gear) - #501-15
This is press-on style pinion gear!
-
DUBICK PINION 48 PITCH, 16T, 0° angle, BRASS (This is press-on style pinion gear) - #501-16
DUBICK PINION 48 PITCH, 16T, 0° angle, BRASS (This is press-on style pinion gear) - #501-16
This is press-on style pinion gear!
-
DUBICK Armature bronze spacers .181" (4.6 mm) thick, 2 pcs. - #4034
DUBICK Armature bronze spacers .181" (4.6 mm) thick, 2 pcs. - #4034
-
DUBICK 2 mm, .22" (5,5 mm) thick aluminium axle spacer, 1 pc. - #712-5.5
DUBICK 2 mm, .22" (5,5 mm) thick aluminium axle spacer, 1 pc. - #712-5.5
-
DUBICK 2 mm, .24" (6 mm) thick aluminium axle spacer, 1 pc. - #712-6
DUBICK 2 mm, .24" (6 mm) thick aluminium axle spacer, 1 pc. - #712-6
-
DUBICK 2 mm, .26" (6,5 mm) thick aluminium axle spacer, 1 pc. - #712-6.5
DUBICK 2 mm, .26" (6,5 mm) thick aluminium axle spacer, 1 pc. - #712-6.5
-
DUBICK JK style body mounting clips, pair - #601
DUBICK JK style body mounting clips, pair - #601
Body mounting clip - same size as JK 9008
-
DUBICK 2 mm, .28" (7 mm) thick aluminium axle spacer, 1 pc. - #712-7
DUBICK 2 mm, .28" (7 mm) thick aluminium axle spacer, 1 pc. - #712-7
-
DUBICK Set #1 of 2 mm inside diameter aluminium tubes ( 5.5 mm (.22"), 6 mm (.24"), 6.5 mm (.26"), 7 mm (.28")) - #712
DUBICK Set of 2 mm inside diameter aluminium tubes - #712
In set 1 pc of each size: 5.5 mm (.22"), 6 mm (.24"), 6.5 mm (.26"), 7 mm (.28")
