DUBICK Engineering

• 

  DUBICK gold plated short guide clips. Made special for new RED FOX guides. (But also fit for all other guides), 1 pair - #DB701

  DUBICK gold plated short guide clips. Made special for new RED FOX guides. (But also fit for all other guides), 1 pair (NEW!)

  1.54 ₤

• 

  DUBICK FANAT Electronic controller with banana plugs - #720BP

  DUBICK Electronic controller

  - suitable for all classes of models;
  - adjust the sharpness of the transistor;
  - high quality 30 amp transistor;
  - electronic CHOKE;
  - 30-speed gold-plated contact block;
  - bronze contacts for maximum speed and braking;
  - built-in voltmeter;
  - complete protection against incorrect switching on.

  193.55 ₤

• 

  DUBICK Reinforcement tape for pin hole, 30 x 180 mm (1,18" x 7,1") - #707

  DUBICK Reinforcement tape for pin hole, 30 x 180 mm (1,18" x 7,1") - #707

  1.07 ₤

• 

  DUBICK 2024 ES 1/32 Eurosport Chassis Assembled w/out ballbearings - #ES32

  All chassis starting from 2016 will be made of German high-carbon structural steel 1 mm thick. This is the same material that is used the world's leading chassis manufacturers.

  116.42 ₤

• 

  DUBICK Lead wire retainers, 2 pcs. - #710

  DUBICK Lead wire retainers, 2 pcs.

  0.28 ₤

• 

  DUBICK 61/39 QUALITY SOLDER in storage tube, diameter 1mm, long 6 feet (1.8 m), 1 pc. - #211

  DUBICK 61/39 QUALITY SOLDER in storage tube, diameter 1mm, long 6 feet (1.8 m), 1 pc. - #211

  1.50 ₤

• 

  DUBICK SEVEN-DIODES controller w/alligator clips - #727-7AC

  DUBICK SEVEN-DIODES controller w/alligator clips

  Variable brake for all motors up to 12 groups (Johnson, Hawk group, 16 & 12 group motors).

  100.33 ₤

• 

  DUBICK Anodized spring cups / 3 coil springs - #716

  DUBICK Anodized spring cups /3 coil springs

  3.16 ₤

• 

  DUBICK Engineering 2020 Open 12 chassis assembled without ballbearings - #122020

  All chassis starting from 2016 will be made of German high-carbon structural steel 1 mm thick. This is the same material that is used the world's leading chassis manufacturers.

  116.42 ₤

• 

  DUBICK Adjustable DUBICK Fanat PRO controller chip

  DUBICK Adjustable DUBICK Fanat PRO controller chip

  31.60 ₤

• 

  DUBICK Electronic controller FANAT Pro

  DUBICK Electronic controller FANAT Pro

  -suitable for all classes of models;
  -antibrake, antibrake correction;
  -electronic CHOKE;
  -Slow Attach/ fast Attachk function (innovation!!!)
  -15 chips;
  -built-in voltmeter;
  -gold-plated contact block;
  -holders for track board;
  -Transistor Correction

  592.50 ₤

• 

  DUBICK Controller chip 29 Ohm for DUBICK Electronic controller - #722-29

  DUBICK Controller chip 29 Ohm for DUBICK Electronic controller

  9.48 ₤

• 

  DUBICK Controller chip 58 Ohm for DUBICK Electronic controller - #722-58

  DUBICK Controller chip 58 Ohm for DUBICK Electronic controller

  9.48 ₤

• 

  DUBICK Anodized spring cups / 5 coil springs - #717

  DUBICK Anodized spring cups / 5 coil springs

  3.16 ₤

• 

  DUBICK Electronic controller Pro version

  DUBICK Electronic controller Pro version

  • -suitable for all classes of models;
  • -more functional than S&K, Kobis or DiFalco controllers;
  • -antibrake, antibrake correction;
  • -wire CHOKE;

  -traction control;

  • -one or two transistors in use;
  • -adjust the sharpness of the transistor;
  • -15 chips;
  • -built-in voltmeter;
  • -gold-plated contact block;
  • -full protection against incorrect switching on.

  1 106.00 ₤

• 

  DUBICK .004" (0.1 mm) Precision steel guide spacers, 6 pcs. - #708

  DUBICK .004" (0.1 mm) Precision steel guide spacers, 6 pcs.

  1.50 ₤

• 

  DUBICK Pinion gear 48 pitch, 6T, 2 mm bore, brass (This is solder style pinion gear) - #501-6

  48 pitch Straight stainless steel 6 tooth pinion gears

  IN STOCK!

  
  

  2.21 ₤

• 

  DUBICK Precut Brass pin tubes, length 10.8 mm, 4 pcs.- #406

  DUBICK Precut Brass pin tubes, length 10.8 mm, 4 pcs.- #406

  Brass pin tubing for chassis 10.8 mm -4/10 of an inch.

  0.75 ₤

• 

  DUBICK Precut Brass pin tubes, length 10.8 mm, storage tube (24 pcs.) - #407

  DUBICK Precut Brass pin tubes, length 10.8 mm, storage tube (24 pcs.) - #407

  Brass pin tubing for chassis 10.8 mm -4/10 of an inch

  4.35 ₤

• 

  DUBICK Diamond hone for increase inside tire diameter till 10,5 mm (0,413")

  DUBICK Diamond hone for increase inside tire diameter till 10,5 mm (0,413")

  51.35 ₤

• 

  DUBICK Pinion gear 48 pitch, 7T, 2 mm bore, brass (This is solder style pinion gear) - #DB501-7

  48 pitch Straight stainless steel 7 tooth pinion gears

  IN STOCK!

  
  

  2.21 ₤

• 

  DUBICK Lead sheet thickness 0.5 mm, 50 х 50 mm (.019", 1.968" x 1.968") with a 3M selfstick adhesive tape - #209

  DUBICK Lead sheet thickness 0.5 mm, 50 х 50 mm (.019", 1.968" x 1.968") with a 3M selfstick adhesive tape - #209

  Lead sheet thickness 0.5 mm, 50 х 50 mm with a adhesive tape can help you to configure your chassis. 
  The presence of stick layer eliminates the need for glue application and simplifies the work!

  0.71 ₤

• 

  DUBICK Lead sheet thickness 1 mm, 50 х 50 mm (.039", 1.968" x 1.968") with a 3M selfstick adhesive tape - #210

  DUBICK Lead sheet thickness 1 mm, 50 х 50 mm (.039", 1.968" x 1.968") with a 3M selfstick adhesive tape - #210

  Lead sheet thickness 1 mm, 50 х 50 mm with a adhesive tape can help you to configure your chassis. 
  The presence of stick layer eliminates the need for glue application and simplifies the work!

  0.71 ₤

• 

  DUBICK Controller chip 78 Ohm for DUBICK Electronic controller - #722-78

  DUBICK Controller chip 78 Ohm for DUBICK Electronic controller 

  9.48 ₤

• 

  DUBICK Plastic box 75 х 132 х 16 mm (2.96" x 5.2" x 0.63") w/12 individual boxes - #DB214

  DUBICK Plastic box 75 х 132 х 16 mm (2.96" x 5.2" x 0.63") w/12 individual boxes

  • Material: plastic with transparent cover.
  • Dimension, mm (in.): 75 х 132 х 16 mm (2.96" x 5.2" x 0.63").
  • Quantity of sections, pcs.: 40.
  • Small storage box for parts great for storing pinions etc.

  3.95 ₤

• 

  DUBICK Plastic box 104 х 175 х 22 mm (4.09" x 6.89" x 0.87") w/15 configurable sections - #DB215

  DUBICK Plastic box 104 х 175 х 22 mm (4.09" x 6.89" x 0.87") w/15 configurable sections - #DB215

  • Material: plastic with transparent cover.
  • Dimension, mm (in.): 104 х 175 х 22 mm (4.09" x 6.89" x 0.87").
  • Quantity of configurable sections, pcs.: 15.
  • Plastic parts box like the DE214 but bigger

  5.14 ₤

• 

  DUBICK Controller chip 95 Ohm for DUBICK Electronic controller - #722-95

  DUBICK Controller chip 95 Ohm for DUBICK Electronic controller

  9.48 ₤

• 

  DUBICK Controller chip 113 Ohm for DUBICK Electronic controller - #722-113

  DUBICK Controller chip 113 Ohm for DUBICK Electronic controller

  9.48 ₤

• 

  DUBICK Controller chip 144 Ohm for DUBICK Electronic controller - #722-144

  DUBICK Controller chip 144 Ohm for DUBICK Electronic controller

  9.48 ₤

• 

  DUBICK Controller chip 194 Ohm for DUBICK Electronic controller - #722-194

  DUBICK Controller chip 194 Ohm for DUBICK Electronic controller

  9.48 ₤

• 

  DUBICK Controller chip 238 Ohm for DUBICK Electronic controller - #722-238

  DUBICK Controller chip 238 Ohm for DUBICK Electronic controller

  9.48 ₤

• 

  DUBICK Controller chip 290 Ohm for DUBICK Electronic controller - #722-290

  DUBICK Controller chip 290 Ohm for DUBICK Electronic controller

  9.48 ₤

• 

  DUBICK Controller chip 319 Ohm for DUBICK Electronic controller - #722-319

  DUBICK Controller chip 319 Ohm for DUBICK Electronic controller

  9.48 ₤

• 

  DUBICK Controller chip 348 Ohm for DUBICK Electronic controller - #722-348

  DUBICK Controller chip 348 Ohm for DUBICK Electronic controller

  9.48 ₤

• 

  DUBICK Controller chip 377 Ohm for DUBICK Electronic controller - #722-377

  DUBICK Controller chip 377 Ohm for DUBICK Electronic controller

  9.48 ₤

• 

  DUBICK Controller chip (custom resistance) for DUBICK Electronic controller

  DUBICK Controller chip (custom resistance) for DUBICK Electronic controller

  11.85 ₤

• 

  DUBICK TECH BLOCK WITH MAGNETS - #DB205

  DUBICK TECH BLOCK WITH MAGNETS - #DB205

  Textolite tech block for models with fixed samarium-cobalt magnets. It is made with a cut zone of guide and rear wheels. Has an even working plane.

  15.01 ₤

• 

  DUBICK Diamond hone for increase inside tire diameter till 11 mm (0,433")

  DUBICK Diamond hone for increase inside tire diameter till 11 mm (0,433")

  51.35 ₤

• 

  DUBICK Holder for the armatures & armatures in the tubes

  DUBICK Holder for the armatures & armatures in the tubes

  5.53 ₤

• 

  DUBICK Traditional flat controller trigger - #726

  DUBICK Traditional flat controller trigger - #DB726

  Same as Parma finger trigger profile. Suitable for Parma, DiFalco or JK controllers. Has an additional brass tube for spring-loaded moving contact.

  6.87 ₤

• 

  DUBICK 4/40" x 1/8" set screws, 1 tube (12 pcs.) - #DB399

  DUBICK 4/40" x 1/8" set screws, 1 tube (12 pcs.) - #DB399

  Tire and gear size.

  2.52 ₤

• 

  DUBICK Tweezers stainless steel, non-magnetic - #DB715

  DUBICK Tweezers stainless steel, non-magnetic - #DB715

  Perfect for work with small parts! 

  5.27 ₤

• 

  DUBICK VISCOSE SPONGE FOR CLEANING SOLDERING IRON TIP, 42 х 54 х 6 mm (1.65" x 2.13" x 0.24") - #DB212

  DUBICK VISCOSE SPONGE FOR CLEANING SOLDERING IRON TIP, 42 х 54 х 6 mm (1.65" x 2.13" x 0.24") - #DB212

  Viscose sponge for cleaning soldering iron tip

    

  0.79 ₤

• 

  DUBICK Blue viscose sponge for cleaning soldering iron tip, 65 х 65 х 7 mm (2.55" x 2.55" x 0.28") - #DB2121

  DUBICK Blue viscose sponge for cleaning soldering iron tip, 65 х 65 х 7 mm (2.55" x 2.55" x 0.28") - #DB2121

  2.05 ₤

• 

  DUBICK PINION GEAR 48 PITCH, 8T, 2 mm bore, BRASS (This is press-on style pinion gear) - #DB501-8

  DUBICK PINION GEAR 48 PITCH, 8T, 2 mm bore, BRASS

  This is press-on style pinion gear

  0.71 ₤

• 

  DUBICK 4/40" x 1/8" set screws, bulk pack of 25 pcs. - #DB400

  DUBICK 4/40" x 1/8" set screws, bulk pack of 25 pcs. - #DB400

  Tire and gear size.

  4.57 ₤

• 

  DUBICK 4/40" x 1/8" set screws, tube (50 pcs.) - #DB401

  DUBICK 4/40" x 1/8" set screws, tube (50 pcs.) - #DB401

  Tire and gear size.

  9.00 ₤

• 

  DUBICK 4/40" x 1/8" set screws, tube (100 pcs.) - #DB402

  DUBICK 4/40" x 1/8" set screws, tube (100 pcs.) - #DB402

  Tire and gear size.

  17.06 ₤

• 

  DUBICK Set of contacts for the controller. Made from brass and GOLD PLATED - #714

  DUBICK set of contacts for the controller. Made from brass and GOLD PLATED.

  Fit for Parma, Jk and RedFox controller triggers. Full analog Parma #355D TURBO CONTACTS & TERMINALS and fit for Parma turbo controller frame.

  9.48 ₤

• 

  DUBICK .01" (0.25 mm) Precision steel guide spacers, 6 pcs. - #DB709

  DUBICK .01" (0.25 mm) Precision steel guide spacers, 6 pcs.

  1.07 ₤

• 

  DUBICK Precut Brass pin tubes, length 11.8 mm, 4 pcs.- #DB4081

  DUBICK Precut Brass pin tubes, length 11.8 mm, 4 pcs.- #DB4081

  0.75 ₤

• 

  DUBICK Precut Brass pin tubes, length 11.8 mm, storage tube (24 pcs.) - #DB409

  DUBICK Precut Brass pin tubes, length 11.8 mm, storage tube (24 pcs.) - #DB409

  4.35 ₤

• 

  DUBICK Desktop organizer for working with small parts 3" x 4 1/2" x .4" (76,2 × 115 × 10 mm). Has a built-in magnet - #DB704

  DUBICK Desktop organizer for working with small parts 3" x 4 1/2" x .4" (76,2 × 115 × 10 mm). Has a built-in magnet - #DB704

  6.65 ₤

• 

  DUBICK TECH BLOCK WITHOUT MAGNETS - #DB2051

  DUBICK TECH BLOCK WITHOUT MAGNETS - #DB2051

  14.22 ₤

• 

  DUBICK gold plated long guide clips. Made special for new RED FOX guides. (But also fit for all other guides), 1 pair - #DB702

  DUBICK gold plated long guide clips. Made special for new RED FOX guides. (But also fit for all other guides), 1 pair

  2.13 ₤

• 

  DUBICK gold plated guide clips with crimping for wires. Made for new RED FOX guides.(Fit for all other guides), 1 pair - #DB703

  DUBICK gold plated guide clips with crimping for wires. Made for new RED FOX guides.(Fit for all other guides), 1 pair

  3.08 ₤

• 

  DUBICK Engineering 2024 F1-32 chassis assembled without ballbearings - #DBF1

  All chassis starting from 2016 will be made of German high-carbon structural steel 1 mm thick. This is the same material that is used the world's leading chassis manufacturers.

  The chassis comes with a front wheels

  
  

  116.42 ₤

• 

  DUBICK 0- 15V, 17A Power Supply. 110V or 220V. Weight 750 gr. Dimensions: 122 x 70 x 208 mm.

  We are happy present our new Power Supply!
  It is two power supply in one!
  - In the kit there is an additional block adapter on 10 Volts and 10 Amperes, for simultaneous work with several engines or tools
  - ability to accurately adjust the current and voltage.
  - The range of voltage adjustment is from 0 to 15 Volts and current from 0 to 17 Amps.
  - Accuracy of adjustment to 0.01 both voltage and current.
  - Ability to work from 110 and 220 Volts.
  - The unit can be controlled via Bluetooth.
  - There is also a USB Charger with a maximum current of up to 3 Amps.
  - Connection of a soldering iron is possible (possible order extra solder iron like on picture)
  - Crocodile wires are included.
  - The weight of the entire set of 960 grams.
  - Dimensions: 122 x 70 x 208 mm.

  197.50 ₤

• 

  DUBICK DIAMOND COMMUTATOR CUTTING TOOL for arms with cup - #DB213

  DUBICK DIAMOND COMMUTATOR CUTTING TOOL for arms with cup - #DB213

  79.00 ₤

• 

  Dubick Egineering Power supply with the ability to accurately adjust the amperage and voltage. The range of voltage regulating from 0 to 15 Volts and amperage from 0 to 12 Amperes. The adjustment accuracy is up to 0.01 both voltage and amperage. Ability to work from 110 and 220 volts. USB Charger. Wires are attached. Weight 850 Grams. Dimensions: 122 x 70 x 208 mm.

  185.65 ₤

• 

  DUBICK 3 coil motor springs, steel, pair - #DB600

  DUBICK 3 coil motor springs, steel, pair - #DB600

  3 coil springs for group 12 and higher motors. Made from hardened steel - one pair

  1.11 ₤

• 

  DUBICK Panda 55,000 rpm 12V motor - #DB750

  DUBICK Panda 55,000 rpm 12V motor - #DB750

  Fast and reliable FK group motor.

  55 turns 28 AWG wire

  Carbon brushes. Short armature shaft.

  7.90 ₤

• 

  DUBICK Rear bridge for the chassis "TEAPOT" 1/24 (model width 83 mm, rims width 18 mm, brigde width 43.5 mm)

  DUBICK Rear bridge for the chassis "TEAPOT" 1/24 (model width 83 mm, rims width 18 mm, brigde width 43.5 mm)

  Suitable for 16 mm gears.

  1.57 ₤

• 

  DUBICK diamond drum for tire truer BSV, 70 grit (grain diameter 0,315 mm) - #DB718

  DUBICK Diamond drum for tire truer BSV, grain 0,3/0 mm

  71.10 ₤

• 

  DUBICK Diamond drum for HUDY tire truer, 60 grit (grain diametr 0,250 mm) - #751

  DUBICK Diamond drum for HUDY tire truer, 60 grit (grain diametr 0,250 mm) - #751

  94.80 ₤

• 

  DUBICK Ballbearing 2 х 5 х 2,3 mm flanged, shielded, 7 balls, pair - #DB608

  DUBICK Ballbearing 2 х 5 х 2,3 mm flanged, shielded, 7 balls, pair - #DB608

  4.74 ₤

• 

  DUBICK Pinion 64 pitch, 9T , 0° angle, 2 mm bore, brass (This is press-on style pinion gear) - #DB502-9

  Pinion 64 pitch, 9T , 0° angle,  2 mm bore, brass

  This is press-on style pinion gear

  1.34 ₤

• 

  DUBICK Precision Ballbearing 2 х 5 х 2.3 mm, flanged, shielded - #DB607

  DUBICK Precision Ballbearing 2 х 5 х 2.3 mm, flanged, shielded - #DB607

  2.37 ₤

• 

  DUBICK Rear bridge for the chassis "SUPER-TEAPOT" 1/24 (w/hole to the motor)

  DUBICK Rear bridge for the chassis "SUPER-TEAPOT" 1/24 (w/hole to the motor)

  3.95 ₤

• 

  DUBICK Universal kit for assembling body mounting unit of the "Teapot 1/32" & "Teapot 1/24" models. Includes 4 pre-cut tubes. Suitable for JK clips #9008 or #9010

  DUBICK Universal kit for assembling body mounting unit of the "Teapot 1/32" & "Teapot 1/24" models. Includes 4 pre-cut tubes. Suitable for JK clips #9008 or #9010 

  1.58 ₤

• 

  DUBICK Kit for assembly mini-slot car box "Sportsman Working Place" for childrens

  DUBICK Kit for assembly mini-slot car box "Sportsman Working Place" for childrens 

  Parameters:

  • Length, mm: 350 (+/- 10-20 mm);
  • Width, mm: 210 (+/- 10-20 mm);
  • Height, mm: 200 (+/- 10-20 mm);
  • + handle for carrying.

  15.80 ₤

• 

  DUBICK Pinion 64 pitch, 10T , 0° angle, 2 mm bore, brass (This is press-on style pinion gear) - #DB502-10

  Pinion 64 pitch, 10T , 0° angle,  2 mm bore, brass

  This is press-on style pinion gear!

  1.54 ₤

• 

  DUBICK Lexan (polycarbonate) for body reinforcement, w/sticky layer 3M, thickness .005" (0.125 mm), size 50x170 mm - #DB2070

  Lexan for body reinforcement

  Parameters

  • Thickness: .005" (0.125 mm)
  • Size: 50x170 mm

  1.58 ₤

• 

  DUBICK LEXAN (POLYCARBONATE) FOR BODY REINFORCEMENT, W/STICKY LAYER 3M, thickness .005" (0.125 mm), size 50x240 mm - #DB2070

  Lexan for body reinforcement

  Parameters

  • Thickness: .005" (0.125 mm)
  • Size: 50x240 mm

  1.58 ₤

• 

  DUBICK Diamond tire file (w/big & small grain of diamond) - #767

  DUBICK Diamond tire file (w/big & small grain of diamond) - #767

  23.70 ₤

• 

  DUBUCK Precision Ballbearing 2 х 5 х 2.5 mm, unshielded - #DB605

  Ballbearing 2 х 5 х 2.5 mm, unflanged - #DB605

  3.95 ₤

• 

  DUBICK PINION GEAR 48 PITCH, 9T, 2 mm bore, BRASS (This is press-on style pinion gear) - #DB501-9

  DUBICK PINION GEAR 48 PITCH, 9T, 2 mm bore, BRASS

  This is press-on style pinion gear

  1.07 ₤

• 

  DUBICK Precision Ballbearing 2 х 6 х 2,3 mm, unflanged - #DB606

  DUBICK Precision Ballbearing 2 х 6 х 2,3 mm, unflanged - #DB606

  2.37 ₤

• 

  DUBICK PINION GEAR 48 PITCH, 10T, 2 mm bore, BRASS (This is press-on style pinion gear) - #DB501-10

  DUBICK PINION GEAR 48 PITCH, 10T, 2 mm bore, BRASS

  This is press-on style pinion gear

  0.79 ₤

• 

  Dubick Diamond brush radius tool dia. 188" (4.77 mm) - #768-188

  Dubick Diamond brush radius tool dia. 188" (4.77 mm) - #768-188

  15.80 ₤

• 

  Dubick Diamond brush radius tool dia. 193" (4.90 mm) - #768-193

  Dubick Diamond brush radius tool dia. 193" (4.90 mm) - #768-193

  15.80 ₤

• 

  Dubick Diamond brush radius tool dia. 197" (5.00 mm) - #768-197

  Dubick Diamond brush radius tool dia. 197" (5.00 mm) - #768-197

  15.80 ₤

• 

  Dubick Diamond brush radius tool dia. 202" (5.13 mm) - #768-202

  Dubick Diamond brush radius tool dia. 202" (5.13 mm) - #768-202

  15.80 ₤

• 

  Dubick Diamond brush radius tool dia. 207" (5.25 mm) - #768-207

  Dubick Diamond brush radius tool dia. 207" (5.25 mm) - #768-207

  15.80 ₤

• 

  Dubick Diamond brush radius tool dia. 211" (5.36 mm) - #768-211

  Dubick Diamond brush radius tool dia. 211" (5.36 mm) - #768-211

  15.80 ₤

• 

  DUBICK SET OF STEEL PROBES FOR MEASUREMENT OF CLEARANCE, 20 pcs from 0,05 to 1 mm - #DB206

  Thickness in set: - 0,05 mm/ 0,1 mm/ 0,15 mm/ 0,2 mm/ 0,25 mm/ 0,3 mm/ 0,35 mm/ 0,4 mm/ 0,45 mm/ 0,5 mm/ 0,55 mm/ 0,6 mm/ 0,65 mm/ 0,7 mm/ 0,75 mm/ 0,8 mm/ 0,85 mm/ 0,9 mm/ 0,95 mm/ 1 mm, respectively

  The set is more than enough for the most detailed measurement of clearance!

  7.90 ₤

• 

  DUBICK Controller spring - #724

  DUBICK Controller spring - #724

  0.79 ₤

• 

  DUBICK AXLE Ballbearing 3/32" х 3/16" х 3/32" (2.36 х 4.76 х 2.36 mm) flanged shielded, 7 balls, pair - #DB609

  DUBICK AXLE Ballbearing 3/32" х 3/16" х 3/32" (2.36 х 4.76 х 2.36 mm)  flanged shielded, 7 balls, pair - #DB609

  Flanged ballbearings for rear bridge

  4.74 ₤

• 

  DUBICK UHU CONTACT GLUE Schuh&Leder FOR TIRES, flacon 33 ml - #DB700

  Excellent glue for tires, better than the "moment" and "88".

  3.16 ₤

• 

  DUBICK 2 mm, .04" (1 mm) thick aluminium axle spacer, 1 pc. - #713-1

  DUBICK 2 mm, .04" (1 mm) thick aluminium axle spacer, 1 pc. - #713-1

  0.24 ₤

• 

  DUBICK 2 mm, .059" (1,5 mm) thick aluminium axle spacer, 1 pc. - #DB713-1.5

  DUBICK 2 mm, .059" (1,5 mm) thick aluminium axle spacer, 1 pc. - #DB713-1.5

  0.24 ₤

• 

  DUBICK LEXAN (POLYCARBONATE) FOR BODY REINFORCEMENT, W/STICKY LAYER 3M, thickness .007" (0.175 mm), size 50x180 mm - #DB2071

  Lexan for body reinforcement

  Parameters

  • Thickness: .007" (0.175 mm)
  • Size: 50x180 mm

  
  

  1.58 ₤

• 

  DUBICK LEXAN (POLYCARBONATE) FOR BODY REINFORCEMENT, W/STICKY LAYER 3M, thickness .010" (0.25 mm), size 50x180 mm - #DB2072

  Lexan for body reinforcement

  Parameters

  • Thickness: .010" (0.25 mm)
  • Size: 50x180 mm

  1.58 ₤

• 

  DUBICK 3M reinforced strapping tape, linear reinforcement, 12 mm x 50 m

  DUBICK 3M reinforced strapping tape, linear reinforcement, 12 mm x 50 m

  The original American 3M. Reinforced with nylon tape. The best material for reinforcing and repairing polycarbonate and plastic models bodies.

  3.56 ₤

• 

  DUBICK 2 mm, .079" (2 mm) thick aluminium axle spacer, 1 pc. - #DB713-2

  DUBICK 2 mm, .079" (2 mm) thick aluminium axle spacer, 1 pc. - #DB713-2

  0.24 ₤

• 

  DUBICK 2 mm, .098" (2,5 mm) thick aluminium axle spacer, 1 pc. - #DB713-2.5

  DUBICK 2 mm, .098" (2,5 mm) thick aluminium axle spacer, 1 pc. - #DB713-2.5

  0.24 ₤

• 

  DUBICK Set #2 of 2 mm inside diameter aluminium tubes (1 mm (.04"), 1.5 mm (.059"), 2 mm (.079"), 2.5 mm (.098")) - #713

  DUBICK Set #2 of 2 mm inside diameter aluminium tubes (1 mm (.04"), 1.5 mm (.059"), 2 mm (.079"), 2.5 mm (.098")) - #713

  In set 2 pc of each size: 1 mm (.04"), 1.5 mm (.059"), 2 mm (.079"), 2.5 mm (.098").

  1.98 ₤

• 

  DUBICK STAND FOR STORAGE WHEELS BOTTLES Ø23.5 mm (JK, Alpha), 88 х 117 mm, acrylic- #DB203-23

  DUBICK STAND FOR STORAGE WHEELS BOTTLES Ø23.5 mm (JK, Alpha), 88 х 117 mm, acrylic- #DB203-23

  PARAMETERS

  • Dia. of wheels bottles, mm: 23,5 (JK, Alpha)
  • Quantity of holes for bottles, pcs: 12
  • Size, mm: 88x17
  • Material: acrylic

  9.68 ₤

• 

  DUBICK PINION 48 PITCH, 11T, 0° angle 2 mm bore, BRASS (This is press-on style pinion gear) - #DB501-11

  DUBICK PINION 48 PITCH, 11T, 0° angle 2 mm bore, BRASS

  This is press-on style pinion gear

  1.98 ₤

• 

  DUBICK STAND FOR STORAGE WHEELS BOTTLES Ø27 mm (PSE, Alpha Large), 103 x 137 mm, acrylic - #DB203-27

  DUBICK STAND FOR STORAGE WHEELS BOTTLES Ø27 mm (PSE, Alpha Large), 103 x 137 mm, acrylic - #DB203-27

  PARAMETERS

  • Dia. of wheels bottles, mm: 27 (PSE, Alpha Large)
  • Quantity of holes for bottles, pcs: 12
  • Size, mm: 103x137
  • Material: acrylic

  9.68 ₤

• 

  DUBICK Diamond motor brush tool (for shunting) - #766

  DUBICK Diamond motor brush tool (for shunting) - #766

  15.80 ₤

• 

  DUBICK MG TOOL FOR PREPARING MOTOR BRUSHES W/DIAMOND WHEEL- #DB201

  A tool that every modelist needs! With it's help quickly and accurately prepare motor brushes for any motors! Comes with a diamond wheel

  Tool for motor brushes (horizontal or vertical). A more advanced design of the turtle. includes anodised knurled grip and diamond coated brush radius tool diameter 5,2 mm (.208")

  54.51 ₤

• 

  DUBICK F1 motor adjustment tool for crowns gears with 2 mm axle, 1.5 mm motor shaft and 0.2 mm offset - #DB711

  DUBICK F1 motor adjustment tool for crowns gears with 2 mm axle, 1.5 mm motor shaft and 0.2 mm offset - #DB711

  Special for 5 and 6 teeth 72 pitch pinions. 0.2 mm offset allow instal down F1 motor for more low center of gravity, but not so dangerous like 0.5 mm offset.

  6.65 ₤

• 

  DUBICK Engineering F1 motor adjustment tool for crowns gears with 3/32" (2.36 mm) axle, 1.5 mm motor shaft and 0.2 mm offset

  DUBICK Engineering F1 motor adjustment tool for crowns gears with 3/32" (2.36 mm) axle, 1.5 mm motor shaft and 0.2 mm offset

  Special for 5 and 6 teeth 72 pitch pinions. 0.2 mm offset allow instal down F1 motor for more low center of gravity, but not so dangerous like 0.5 mm offset.

  6.65 ₤

• 

  DUBICK .050" Aluminium allen wrench w/guide tool 3/8" (9,5 mm), anodized - #DB604

  DUBICK .050" Aluminium allen wrench w/guide tool 3/8" (9,5 mm), anodized - #DB604

  15.79 ₤

• 

  Dubick Egineering Power supply with the ability to accurately adjust the amperage and voltage. The range of voltage regulating from 0 to 15 Volts and amperage from 0 to 12 Amperes. The adjustment accuracy is up to 0.01 both voltage and amperage. Ability to work from 110 and 220 volts. USB Charger. Wires are attached. Weight 850 Grams. Dimensions: 122 x 70 x 208 mm.

  154.05 ₤

• 

  DUBICK 3M REINFORCED STRAPPING TAPE, 12 mm x 50 m - #DB2073

  3m Reinforced strapping tape, 12mm x 50m

  The original American 3M. Reinforced with nylon tape. The best material for reinforcing and repairing polycarbonate and plastic models bodies.

  9.48 ₤

• 

  DUBICK 3M REINFORCED STRAPPING TAPE, 25 mm x 50 m - #DB2074

  3m Reinforced strapping tape, 25mm x 50m

  The original American 3M. Reinforced with nylon tape. The best material for reinforcing and repairing polycarbonate and plastic models bodies.

  17.38 ₤

• 

  DUBICK 3M REINFORCED STRAPPING TAPE, 50 mm x 50 m - #DB2075

  3m Reinforced strapping tape, 50mm x 50m

  The original American 3M. Reinforced with nylon tape. The best material for reinforcing and repairing polycarbonate and plastic models bodies.

  23.70 ₤

• 

  DUBICK Axle ballbearing 1/8" x 1/4" (3.15 mm x 6.35 mm), sheilded, flanged, pair - #DE719

  DUBICK Axle ballbearing 1/8" x 1/4" (3.15 mm x 6.35 mm), sheilded, flanged, pair - #DE719

  4.74 ₤

• 

  DUBICK Engineering 2024 ES 1/24 Eurosport chassis assembled without ballbearings - #DBES24

  All chassis starting from 2016 will be made of German high-carbon structural steel 1 mm thick. This is the same material that is used the world's leading chassis manufacturers.

  116.42 ₤

• 

  DUBICK PINION 48 PITCH, 12T, 0° angle 2 mm bore, BRASS (This is press-on style pinion gear) - #DB501-12

  DUBICK PINION 48 PITCH, 12T, 0° angle 2 mm bore, BRASS

  This is press-on style pinion gear

  1.58 ₤

• 

  DUBICK PINION 48 PITCH, 13T, 0° angle 2 mm bore, BRASS (This is press-on style pinion gear) - #DB501-13

  DUBICK PINION 48 PITCH, 13T, 0° angle 2 mm bore, BRASS

  This is press-on style pinion gear

  1.58 ₤

• 

  DUBICK PINION 48 PITCH, 14T, 0° angle, 3 mm bore, BRASS (This is press-on style pinion gear) - #DB501-14

  DUBICK PINION 48 PITCH, 14T, 0° angle, 3 mm bore, BRASS

  This is press-on style pinion gear

  1.58 ₤

• 

  DUBICK PINION 48 PITCH, 15T, 0° angle, BRASS (This is press-on style pinion gear) - #DB501-15

  DUBICK PINION 48 PITCH, 15T, 0° angle, BRASS (This is press-on style pinion gear) - #501-15

  This is press-on style pinion gear!

  1.58 ₤

• 

  DUBICK PINION 48 PITCH, 16T, 0° angle, BRASS (This is press-on style pinion gear) - #DB501-16

  DUBICK PINION 48 PITCH, 16T, 0° angle, BRASS (This is press-on style pinion gear) - #501-16

  This is press-on style pinion gear!

  1.58 ₤

• 

  DUBICK armature bronze spacers 4.6 mm thick, 2 pcs. - #DB4034

  DUBICK armature bronze spacers 4.6 mm thick, 2 pcs. - #DB4034

  0.43 ₤

• 

  DUBICK 2 mm, .22" (5,5 mm) thick aluminium axle spacer, 1 pc. - #DB712-5.5

  DUBICK 2 mm, .22" (5,5 mm) thick aluminium axle spacer, 1 pc. - #DB712-5.5

  0.24 ₤

• 

  DUBICK 2 mm, .24" (6 mm) thick aluminium axle spacer, 1 pc. - #DB712-6

  DUBICK 2 mm, .24" (6 mm) thick aluminium axle spacer, 1 pc. - #DB712-6

  0.24 ₤

• 

  DUBICK 2 mm, .26" (6,5 mm) thick aluminium axle spacer, 1 pc. - #DB712-6.5

  DUBICK 2 mm, .26" (6,5 mm) thick aluminium axle spacer, 1 pc. - #DB712-6.5

  0.24 ₤

• 

  DUBICK JK style body mounting clips, pair - #DB601

  DUBICK JK style body mounting clips, pair - #DB601

  Body mounting clip - same size as JK 9008

  0.55 ₤

• 

  DUBICK 2 mm, .28" (7 mm) thick aluminium axle spacer, 1 pc. - #DB712-7

  DUBICK 2 mm, .28" (7 mm) thick aluminium axle spacer, 1 pc. - #DB712-7

  0.24 ₤

• 

  DUBICK Set #1 of 2 mm inside diameter aluminium tubes ( 5.5 mm (.22"), 6 mm (.24"), 6.5 mm (.26"), 7 mm (.28")) - #DB712

  DUBICK Set of 2 mm inside diameter aluminium tubes - #DB712

  In set 1 pc of each size: 5.5 mm (.22"), 6 mm (.24"), 6.5 mm (.26"), 7 mm (.28")

  3.16 ₤