DUBICK Engineering
-
DUBICK 61/39 QUALITY SOLDER in storage tube, diameter 1mm, long 6 feet (1.8 m), 1 pc. - #211
DUBICK 61/39 QUALITY SOLDER in storage tube, diameter 1mm, long 6 feet (1.8 m), 1 pc. - #211
-
DUBICK gold plated short guide clips. Made special for new RED FOX guides. (But also fit for all other guides), 1 pair - #DB701
DUBICK gold plated short guide clips. Made special for new RED FOX guides. (But also fit for all other guides), 1 pair (NEW!)
-
DUBICK FANAT Electronic controller with banana plugs - #720BP
DUBICK Electronic controller
- suitable for all classes of models;
- adjust the sharpness of the transistor;
- high quality 30 amp transistor;
- electronic CHOKE;
- 30-speed gold-plated contact block;
- bronze contacts for maximum speed and braking;
- built-in voltmeter;
- complete protection against incorrect switching on. -
DUBICK Reinforcement tape for pin hole, 30 x 180 mm (1,18" x 7,1") - #707
DUBICK Reinforcement tape for pin hole, 30 x 180 mm (1,18" x 7,1") - #707
-
DUBICK 2024 ES 1/32 Eurosport Chassis Assembled w/out ballbearings - #ES32
All chassis starting from 2016 will be made of German high-carbon structural steel 1 mm thick. This is the same material that is used the world's leading chassis manufacturers.
-
DUBICK Lead wire retainers, 2 pcs. - #710
DUBICK Lead wire retainers, 2 pcs.
-
DUBICK SEVEN-DIODES controller w/alligator clips - #727-7AC
DUBICK SEVEN-DIODES controller w/alligator clips
Variable brake for all motors up to 12 groups (Johnson, Hawk group, 16 & 12 group motors).
-
DUBICK Anodized spring cups / 3 coil springs - #716
DUBICK Anodized spring cups /3 coil springs
-
DUBICK Engineering 2020 Open 12 chassis assembled without ballbearings - #122020
All chassis starting from 2016 will be made of German high-carbon structural steel 1 mm thick. This is the same material that is used the world's leading chassis manufacturers.
-
DUBICK Adjustable DUBICK Fanat PRO controller chip
DUBICK Adjustable DUBICK Fanat PRO controller chip
-
DUBICK Electronic controller FANAT Pro
DUBICK Electronic controller FANAT Pro
-suitable for all classes of models;
-antibrake, antibrake correction;
-electronic CHOKE;
-Slow Attach/ fast Attachk function (innovation!!!)
-15 chips;
-built-in voltmeter;
-gold-plated contact block;
-holders for track board;
-Transistor Correction -
DUBICK Controller chip 29 Ohm for DUBICK Electronic controller - #722-29
DUBICK Controller chip 29 Ohm for DUBICK Electronic controller
-
DUBICK Controller chip 58 Ohm for DUBICK Electronic controller - #722-58
DUBICK Controller chip 58 Ohm for DUBICK Electronic controller
-
DUBICK Anodized spring cups / 5 coil springs - #717
DUBICK Anodized spring cups / 5 coil springs
-
DUBICK Electronic controller Pro version
DUBICK Electronic controller Pro version
- -suitable for all classes of models;
- -more functional than S&K, Kobis or DiFalco controllers;
- -antibrake, antibrake correction;
- -wire CHOKE;
-traction control;
- -one or two transistors in use;
- -adjust the sharpness of the transistor;
- -15 chips;
- -built-in voltmeter;
- -gold-plated contact block;
- -full protection against incorrect switching on.
-
DUBICK .004" (0.1 mm) Precision steel guide spacers, 6 pcs. - #708
DUBICK .004" (0.1 mm) Precision steel guide spacers, 6 pcs.
-
DUBICK Pinion gear 48 pitch, 6T, 2 mm bore, brass (This is solder style pinion gear) - #501-6
48 pitch Straight stainless steel 6 tooth pinion gears
IN STOCK!
-
DUBICK Precut Brass pin tubes, length 10.8 mm, 4 pcs.- #406
DUBICK Precut Brass pin tubes, length 10.8 mm, 4 pcs.- #406
Brass pin tubing for chassis 10.8 mm -4/10 of an inch.
-
DUBICK Precut Brass pin tubes, length 10.8 mm, storage tube (24 pcs.) - #407
DUBICK Precut Brass pin tubes, length 10.8 mm, storage tube (24 pcs.) - #407
Brass pin tubing for chassis 10.8 mm -4/10 of an inch
-
DUBICK Diamond hone for increase inside tire diameter till 10,5 mm (0,413")
DUBICK Diamond hone for increase inside tire diameter till 10,5 mm (0,413")
-
DUBICK Pinion gear 48 pitch, 7T, 2 mm bore, brass (This is solder style pinion gear) - #DB501-7
48 pitch Straight stainless steel 7 tooth pinion gears
IN STOCK!
-
DUBICK Lead sheet thickness 0.5 mm, 50 х 50 mm (.019", 1.968" x 1.968") with a 3M selfstick adhesive tape - #209
DUBICK Lead sheet thickness 0.5 mm, 50 х 50 mm (.019", 1.968" x 1.968") with a 3M selfstick adhesive tape - #209
Lead sheet thickness 0.5 mm, 50 х 50 mm with a adhesive tape can help you to configure your chassis.
The presence of stick layer eliminates the need for glue application and simplifies the work! -
DUBICK Lead sheet thickness 1 mm, 50 х 50 mm (.039", 1.968" x 1.968") with a 3M selfstick adhesive tape - #210
DUBICK Lead sheet thickness 1 mm, 50 х 50 mm (.039", 1.968" x 1.968") with a 3M selfstick adhesive tape - #210
Lead sheet thickness 1 mm, 50 х 50 mm with a adhesive tape can help you to configure your chassis.
The presence of stick layer eliminates the need for glue application and simplifies the work! -
DUBICK Controller chip 78 Ohm for DUBICK Electronic controller - #722-78
DUBICK Controller chip 78 Ohm for DUBICK Electronic controller
-
DUBICK Plastic box 75 х 132 х 16 mm (2.96" x 5.2" x 0.63") w/12 individual boxes - #DB214
DUBICK Plastic box 75 х 132 х 16 mm (2.96" x 5.2" x 0.63") w/12 individual boxes
- Material: plastic with transparent cover.
- Dimension, mm (in.): 75 х 132 х 16 mm (2.96" x 5.2" x 0.63").
- Quantity of sections, pcs.: 40.
- Small storage box for parts great for storing pinions etc.
-
DUBICK Plastic box 104 х 175 х 22 mm (4.09" x 6.89" x 0.87") w/15 configurable sections - #DB215
DUBICK Plastic box 104 х 175 х 22 mm (4.09" x 6.89" x 0.87") w/15 configurable sections - #DB215
- Material: plastic with transparent cover.
- Dimension, mm (in.): 104 х 175 х 22 mm (4.09" x 6.89" x 0.87").
- Quantity of configurable sections, pcs.: 15.
- Plastic parts box like the DE214 but bigger
-
DUBICK Controller chip 95 Ohm for DUBICK Electronic controller - #722-95
DUBICK Controller chip 95 Ohm for DUBICK Electronic controller
-
DUBICK Controller chip 113 Ohm for DUBICK Electronic controller - #722-113
DUBICK Controller chip 113 Ohm for DUBICK Electronic controller
-
DUBICK Controller chip 144 Ohm for DUBICK Electronic controller - #722-144
DUBICK Controller chip 144 Ohm for DUBICK Electronic controller
-
DUBICK Controller chip 194 Ohm for DUBICK Electronic controller - #722-194
DUBICK Controller chip 194 Ohm for DUBICK Electronic controller
-
DUBICK Controller chip 238 Ohm for DUBICK Electronic controller - #722-238
DUBICK Controller chip 238 Ohm for DUBICK Electronic controller
-
DUBICK Controller chip 290 Ohm for DUBICK Electronic controller - #722-290
DUBICK Controller chip 290 Ohm for DUBICK Electronic controller
-
DUBICK Controller chip 319 Ohm for DUBICK Electronic controller - #722-319
DUBICK Controller chip 319 Ohm for DUBICK Electronic controller
-
DUBICK Controller chip 348 Ohm for DUBICK Electronic controller - #722-348
DUBICK Controller chip 348 Ohm for DUBICK Electronic controller
-
DUBICK Controller chip 377 Ohm for DUBICK Electronic controller - #722-377
DUBICK Controller chip 377 Ohm for DUBICK Electronic controller
-
DUBICK Controller chip (custom resistance) for DUBICK Electronic controller
DUBICK Controller chip (custom resistance) for DUBICK Electronic controller
-
DUBICK 4/40" x 1/8" set screws, 1 tube (12 pcs.) - #DB399
DUBICK 4/40" x 1/8" set screws, 1 tube (12 pcs.) - #DB399
Tire and gear size.
-
DUBICK 4/40" x 1/8" set screws, bulk pack of 25 pcs. - #DB400
DUBICK 4/40" x 1/8" set screws, bulk pack of 25 pcs. - #DB400
Tire and gear size.
-
DUBICK TECH BLOCK WITH MAGNETS - #DB205
DUBICK TECH BLOCK WITH MAGNETS - #DB205
Textolite tech block for models with fixed samarium-cobalt magnets. It is made with a cut zone of guide and rear wheels. Has an even working plane.
-
DUBICK Diamond hone for increase inside tire diameter till 11 mm (0,433")
DUBICK Diamond hone for increase inside tire diameter till 11 mm (0,433")
-
DUBICK Holder for the armatures & armatures in the tubes
DUBICK Holder for the armatures & armatures in the tubes
-
DUBICK Traditional flat controller trigger - #726
DUBICK Traditional flat controller trigger - #DB726
Same as Parma finger trigger profile. Suitable for Parma, DiFalco or JK controllers. Has an additional brass tube for spring-loaded moving contact.
-
DUBICK 4/40" x 1/8" set screws, tube (50 pcs.) - #DB401
DUBICK 4/40" x 1/8" set screws, tube (50 pcs.) - #DB401
Tire and gear size.
-
DUBICK Tweezers stainless steel, non-magnetic - #DB715
DUBICK Tweezers stainless steel, non-magnetic - #DB715
Perfect for work with small parts!
-
DUBICK VISCOSE SPONGE FOR CLEANING SOLDERING IRON TIP, 42 х 54 х 6 mm (1.65" x 2.13" x 0.24") - #DB212
DUBICK VISCOSE SPONGE FOR CLEANING SOLDERING IRON TIP, 42 х 54 х 6 mm (1.65" x 2.13" x 0.24") - #DB212
Viscose sponge for cleaning soldering iron tip
-
DUBICK Blue viscose sponge for cleaning soldering iron tip, 65 х 65 х 7 mm (2.55" x 2.55" x 0.28") - #DB2121
DUBICK Blue viscose sponge for cleaning soldering iron tip, 65 х 65 х 7 mm (2.55" x 2.55" x 0.28") - #DB2121
-
DUBICK PINION GEAR 48 PITCH, 8T, 2 mm bore, BRASS (This is press-on style pinion gear) - #DB501-8
DUBICK PINION GEAR 48 PITCH, 8T, 2 mm bore, BRASS
This is press-on style pinion gear
-
DUBICK 4/40" x 1/8" set screws, tube (100 pcs.) - #DB402
DUBICK 4/40" x 1/8" set screws, tube (100 pcs.) - #DB402
Tire and gear size.
-
DUBICK Set of contacts for the controller. Made from brass and GOLD PLATED - #714
DUBICK set of contacts for the controller. Made from brass and GOLD PLATED.
Fit for Parma, Jk and RedFox controller triggers. Full analog Parma #355D TURBO CONTACTS & TERMINALS and fit for Parma turbo controller frame.
-
DUBICK .01" (0.25 mm) Precision steel guide spacers, 6 pcs. - #DB709
DUBICK .01" (0.25 mm) Precision steel guide spacers, 6 pcs.
-
DUBICK Precut Brass pin tubes, length 11.8 mm, 4 pcs.- #DB4081
DUBICK Precut Brass pin tubes, length 11.8 mm, 4 pcs.- #DB4081
-
DUBICK Precut Brass pin tubes, length 11.8 mm, storage tube (24 pcs.) - #DB409
DUBICK Precut Brass pin tubes, length 11.8 mm, storage tube (24 pcs.) - #DB409
-
DUBICK Desktop organizer for working with small parts 3" x 4 1/2" x .4" (76,2 × 115 × 10 mm). Has a built-in magnet - #DB704
DUBICK Desktop organizer for working with small parts 3" x 4 1/2" x .4" (76,2 × 115 × 10 mm). Has a built-in magnet - #DB704
-
DUBICK TECH BLOCK WITHOUT MAGNETS - #DB2051
DUBICK TECH BLOCK WITHOUT MAGNETS - #DB2051
-
DUBICK gold plated long guide clips. Made special for new RED FOX guides. (But also fit for all other guides), 1 pair - #DB702
DUBICK gold plated long guide clips. Made special for new RED FOX guides. (But also fit for all other guides), 1 pair
-
DUBICK gold plated guide clips with crimping for wires. Made for new RED FOX guides.(Fit for all other guides), 1 pair - #DB703
DUBICK gold plated guide clips with crimping for wires. Made for new RED FOX guides.(Fit for all other guides), 1 pair
-
DUBICK Engineering 2024 F1-32 chassis assembled without ballbearings - #DBF1
All chassis starting from 2016 will be made of German high-carbon structural steel 1 mm thick. This is the same material that is used the world's leading chassis manufacturers.
The chassis comes with a front wheels
-
DUBICK 0- 15V, 17A Power Supply. 110V or 220V. Weight 750 gr. Dimensions: 122 x 70 x 208 mm.
We are happy present our new Power Supply!
It is two power supply in one!
- In the kit there is an additional block adapter on 10 Volts and 10 Amperes, for simultaneous work with several engines or tools
- ability to accurately adjust the current and voltage.
- The range of voltage adjustment is from 0 to 15 Volts and current from 0 to 17 Amps.
- Accuracy of adjustment to 0.01 both voltage and current.
- Ability to work from 110 and 220 Volts.
- The unit can be controlled via Bluetooth.
- There is also a USB Charger with a maximum current of up to 3 Amps.
- Connection of a soldering iron is possible (possible order extra solder iron like on picture)
- Crocodile wires are included.
- The weight of the entire set of 960 grams.
- Dimensions: 122 x 70 x 208 mm. -
DUBICK DIAMOND COMMUTATOR CUTTING TOOL for arms with cup - #DB213
DUBICK DIAMOND COMMUTATOR CUTTING TOOL for arms with cup - #DB213
-
-
DUBICK 3 coil motor springs, steel, pair - #DB600
DUBICK 3 coil motor springs, steel, pair - #DB600
3 coil springs for group 12 and higher motors. Made from hardened steel - one pair
-
DUBICK Panda 55,000 rpm 12V motor - #DB750
DUBICK Panda 55,000 rpm 12V motor - #DB750
Fast and reliable FK group motor.
55 turns 28 AWG wire
Carbon brushes. Short armature shaft.
-
DUBICK Rear bridge for the chassis "TEAPOT" 1/24 (model width 83 mm, rims width 18 mm, brigde width 43.5 mm)
DUBICK Rear bridge for the chassis "TEAPOT" 1/24 (model width 83 mm, rims width 18 mm, brigde width 43.5 mm)
Suitable for 16 mm gears.
-
DUBICK diamond drum for tire truer BSV, 70 grit (grain diameter 0,315 mm) - #DB718
DUBICK Diamond drum for tire truer BSV, grain 0,3/0 mm
-
DUBICK Diamond drum for HUDY tire truer, 60 grit (grain diametr 0,250 mm) - #751
DUBICK Diamond drum for HUDY tire truer, 60 grit (grain diametr 0,250 mm) - #751
-
DUBICK Ballbearing 2 х 5 х 2,3 mm flanged, shielded, 7 balls, pair - #DB608
DUBICK Ballbearing 2 х 5 х 2,3 mm flanged, shielded, 7 balls, pair - #DB608
-
DUBICK Pinion 64 pitch, 9T , 0° angle, 2 mm bore, brass (This is press-on style pinion gear) - #DB502-9
Pinion 64 pitch, 9T , 0° angle, 2 mm bore, brass
This is press-on style pinion gear
-
DUBICK Precision Ballbearing 2 х 5 х 2.3 mm, flanged, shielded - #DB607
DUBICK Precision Ballbearing 2 х 5 х 2.3 mm, flanged, shielded - #DB607
-
DUBICK Rear bridge for the chassis "SUPER-TEAPOT" 1/24 (w/hole to the motor)
DUBICK Rear bridge for the chassis "SUPER-TEAPOT" 1/24 (w/hole to the motor)
-
DUBICK Universal kit for assembling body mounting unit of the "Teapot 1/32" & "Teapot 1/24" models. Includes 4 pre-cut tubes. Suitable for JK clips #9008 or #9010
DUBICK Universal kit for assembling body mounting unit of the "Teapot 1/32" & "Teapot 1/24" models. Includes 4 pre-cut tubes. Suitable for JK clips #9008 or #9010
-
DUBICK Kit for assembly mini-slot car box "Sportsman Working Place" for childrens
DUBICK Kit for assembly mini-slot car box "Sportsman Working Place" for childrens
Parameters:
- Length, mm: 350 (+/- 10-20 mm);
- Width, mm: 210 (+/- 10-20 mm);
- Height, mm: 200 (+/- 10-20 mm);
- + handle for carrying.
-
DUBICK Pinion 64 pitch, 10T , 0° angle, 2 mm bore, brass (This is press-on style pinion gear) - #DB502-10
Pinion 64 pitch, 10T , 0° angle, 2 mm bore, brass
This is press-on style pinion gear!
-
DUBICK Lexan (polycarbonate) for body reinforcement, w/sticky layer 3M, thickness .005" (0.125 mm), size 50x170 mm - #DB2070
Lexan for body reinforcement
Parameters
- Thickness: .005" (0.125 mm)
- Size: 50x170 mm
-
DUBICK LEXAN (POLYCARBONATE) FOR BODY REINFORCEMENT, W/STICKY LAYER 3M, thickness .005" (0.125 mm), size 50x240 mm - #DB2070
Lexan for body reinforcement
Parameters
- Thickness: .005" (0.125 mm)
- Size: 50x240 mm
-
DUBICK Diamond tire file (w/big & small grain of diamond) - #767
DUBICK Diamond tire file (w/big & small grain of diamond) - #767
-
DUBUCK Precision Ballbearing 2 х 5 х 2.5 mm, unshielded - #DB605
Ballbearing 2 х 5 х 2.5 mm, unflanged - #DB605
-
DUBICK PINION GEAR 48 PITCH, 9T, 2 mm bore, BRASS (This is press-on style pinion gear) - #DB501-9
DUBICK PINION GEAR 48 PITCH, 9T, 2 mm bore, BRASS
This is press-on style pinion gear
-
DUBICK Precision Ballbearing 2 х 6 х 2,3 mm, unflanged - #DB606
DUBICK Precision Ballbearing 2 х 6 х 2,3 mm, unflanged - #DB606
-
DUBICK PINION GEAR 48 PITCH, 10T, 2 mm bore, BRASS (This is press-on style pinion gear) - #DB501-10
DUBICK PINION GEAR 48 PITCH, 10T, 2 mm bore, BRASS
This is press-on style pinion gear
-
Dubick Diamond brush radius tool dia. 188" (4.77 mm) - #768-188
Dubick Diamond brush radius tool dia. 188" (4.77 mm) - #768-188
-
Dubick Diamond brush radius tool dia. 193" (4.90 mm) - #768-193
Dubick Diamond brush radius tool dia. 193" (4.90 mm) - #768-193
-
Dubick Diamond brush radius tool dia. 197" (5.00 mm) - #768-197
Dubick Diamond brush radius tool dia. 197" (5.00 mm) - #768-197
-
Dubick Diamond brush radius tool dia. 202" (5.13 mm) - #768-202
Dubick Diamond brush radius tool dia. 202" (5.13 mm) - #768-202
-
Dubick Diamond brush radius tool dia. 207" (5.25 mm) - #768-207
Dubick Diamond brush radius tool dia. 207" (5.25 mm) - #768-207
-
Dubick Diamond brush radius tool dia. 211" (5.36 mm) - #768-211
Dubick Diamond brush radius tool dia. 211" (5.36 mm) - #768-211
-
DUBICK SET OF STEEL PROBES FOR MEASUREMENT OF CLEARANCE, 20 pcs from 0,05 to 1 mm - #DB206
Thickness in set: - 0,05 mm/ 0,1 mm/ 0,15 mm/ 0,2 mm/ 0,25 mm/ 0,3 mm/ 0,35 mm/ 0,4 mm/ 0,45 mm/ 0,5 mm/ 0,55 mm/ 0,6 mm/ 0,65 mm/ 0,7 mm/ 0,75 mm/ 0,8 mm/ 0,85 mm/ 0,9 mm/ 0,95 mm/ 1 mm, respectively
The set is more than enough for the most detailed measurement of clearance!
-
DUBICK Controller spring - #724
DUBICK Controller spring - #724
-
DUBICK AXLE Ballbearing 3/32" х 3/16" х 3/32" (2.36 х 4.76 х 2.36 mm) flanged shielded, 7 balls, pair - #DB609
DUBICK AXLE Ballbearing 3/32" х 3/16" х 3/32" (2.36 х 4.76 х 2.36 mm) flanged shielded, 7 balls, pair - #DB609
Flanged ballbearings for rear bridge
-
DUBICK UHU CONTACT GLUE Schuh&Leder FOR TIRES, flacon 33 ml - #DB700
Excellent glue for tires, better than the "moment" and "88".
-
DUBICK 2 mm, .04" (1 mm) thick aluminium axle spacer, 1 pc. - #713-1
DUBICK 2 mm, .04" (1 mm) thick aluminium axle spacer, 1 pc. - #713-1
-
DUBICK 2 mm, .059" (1,5 mm) thick aluminium axle spacer, 1 pc. - #DB713-1.5
DUBICK 2 mm, .059" (1,5 mm) thick aluminium axle spacer, 1 pc. - #DB713-1.5
-
DUBICK LEXAN (POLYCARBONATE) FOR BODY REINFORCEMENT, W/STICKY LAYER 3M, thickness .007" (0.175 mm), size 50x180 mm - #DB2071
Lexan for body reinforcement
Parameters
- Thickness: .007" (0.175 mm)
- Size: 50x180 mm
-
DUBICK LEXAN (POLYCARBONATE) FOR BODY REINFORCEMENT, W/STICKY LAYER 3M, thickness .010" (0.25 mm), size 50x180 mm - #DB2072
Lexan for body reinforcement
Parameters
- Thickness: .010" (0.25 mm)
- Size: 50x180 mm
-
DUBICK 3M reinforced strapping tape, linear reinforcement, 12 mm x 50 m
DUBICK 3M reinforced strapping tape, linear reinforcement, 12 mm x 50 m
The original American 3M. Reinforced with nylon tape. The best material for reinforcing and repairing polycarbonate and plastic models bodies.
-
DUBICK 2 mm, .079" (2 mm) thick aluminium axle spacer, 1 pc. - #DB713-2
DUBICK 2 mm, .079" (2 mm) thick aluminium axle spacer, 1 pc. - #DB713-2
-
DUBICK 2 mm, .098" (2,5 mm) thick aluminium axle spacer, 1 pc. - #DB713-2.5
DUBICK 2 mm, .098" (2,5 mm) thick aluminium axle spacer, 1 pc. - #DB713-2.5
-
DUBICK Set #2 of 2 mm inside diameter aluminium tubes (1 mm (.04"), 1.5 mm (.059"), 2 mm (.079"), 2.5 mm (.098")) - #713
DUBICK Set #2 of 2 mm inside diameter aluminium tubes (1 mm (.04"), 1.5 mm (.059"), 2 mm (.079"), 2.5 mm (.098")) - #713
In set 2 pc of each size: 1 mm (.04"), 1.5 mm (.059"), 2 mm (.079"), 2.5 mm (.098").
-
DUBICK STAND FOR STORAGE WHEELS BOTTLES Ø23.5 mm (JK, Alpha), 88 х 117 mm, acrylic- #DB203-23
DUBICK STAND FOR STORAGE WHEELS BOTTLES Ø23.5 mm (JK, Alpha), 88 х 117 mm, acrylic- #DB203-23
PARAMETERS
- Dia. of wheels bottles, mm: 23,5 (JK, Alpha)
- Quantity of holes for bottles, pcs: 12
- Size, mm: 88x17
- Material: acrylic
-
DUBICK PINION 48 PITCH, 11T, 0° angle 2 mm bore, BRASS (This is press-on style pinion gear) - #DB501-11
DUBICK PINION 48 PITCH, 11T, 0° angle 2 mm bore, BRASS
This is press-on style pinion gear
-
DUBICK STAND FOR STORAGE WHEELS BOTTLES Ø27 mm (PSE, Alpha Large), 103 x 137 mm, acrylic - #DB203-27
DUBICK STAND FOR STORAGE WHEELS BOTTLES Ø27 mm (PSE, Alpha Large), 103 x 137 mm, acrylic - #DB203-27
PARAMETERS
- Dia. of wheels bottles, mm: 27 (PSE, Alpha Large)
- Quantity of holes for bottles, pcs: 12
- Size, mm: 103x137
- Material: acrylic
-
DUBICK Diamond motor brush tool (for shunting) - #766
DUBICK Diamond motor brush tool (for shunting) - #766
-
DUBICK MG TOOL FOR PREPARING MOTOR BRUSHES W/DIAMOND WHEEL- #DB201
A tool that every modelist needs! With it's help quickly and accurately prepare motor brushes for any motors! Comes with a diamond wheel
Tool for motor brushes (horizontal or vertical). A more advanced design of the turtle. includes anodised knurled grip and diamond coated brush radius tool diameter 5,2 mm (.208")
-
DUBICK F1 motor adjustment tool for crowns gears with 2 mm axle, 1.5 mm motor shaft and 0.2 mm offset - #DB711
DUBICK F1 motor adjustment tool for crowns gears with 2 mm axle, 1.5 mm motor shaft and 0.2 mm offset - #DB711
Special for 5 and 6 teeth 72 pitch pinions. 0.2 mm offset allow instal down F1 motor for more low center of gravity, but not so dangerous like 0.5 mm offset.
-
DUBICK Engineering F1 motor adjustment tool for crowns gears with 3/32" (2.36 mm) axle, 1.5 mm motor shaft and 0.2 mm offset
DUBICK Engineering F1 motor adjustment tool for crowns gears with 3/32" (2.36 mm) axle, 1.5 mm motor shaft and 0.2 mm offset
Special for 5 and 6 teeth 72 pitch pinions. 0.2 mm offset allow instal down F1 motor for more low center of gravity, but not so dangerous like 0.5 mm offset.
-
DUBICK .050" Aluminium allen wrench w/guide tool 3/8" (9,5 mm), anodized - #DB604
DUBICK .050" Aluminium allen wrench w/guide tool 3/8" (9,5 mm), anodized - #DB604
-
-
DUBICK 3M REINFORCED STRAPPING TAPE, 12 mm x 50 m - #DB2073
3m Reinforced strapping tape, 12mm x 50m
The original American 3M. Reinforced with nylon tape. The best material for reinforcing and repairing polycarbonate and plastic models bodies.
-
DUBICK 3M REINFORCED STRAPPING TAPE, 25 mm x 50 m - #DB2074
3m Reinforced strapping tape, 25mm x 50m
The original American 3M. Reinforced with nylon tape. The best material for reinforcing and repairing polycarbonate and plastic models bodies.
-
DUBICK 3M REINFORCED STRAPPING TAPE, 50 mm x 50 m - #DB2075
3m Reinforced strapping tape, 50mm x 50m
The original American 3M. Reinforced with nylon tape. The best material for reinforcing and repairing polycarbonate and plastic models bodies.
-
DUBICK Axle ballbearing 1/8" x 1/4" (3.15 mm x 6.35 mm), sheilded, flanged, pair - #DE719
DUBICK Axle ballbearing 1/8" x 1/4" (3.15 mm x 6.35 mm), sheilded, flanged, pair - #DE719
-
DUBICK Engineering 2024 ES 1/24 Eurosport chassis assembled without ballbearings - #DBES24
All chassis starting from 2016 will be made of German high-carbon structural steel 1 mm thick. This is the same material that is used the world's leading chassis manufacturers.
-
DUBICK PINION 48 PITCH, 12T, 0° angle 2 mm bore, BRASS (This is press-on style pinion gear) - #DB501-12
DUBICK PINION 48 PITCH, 12T, 0° angle 2 mm bore, BRASS
This is press-on style pinion gear
-
DUBICK PINION 48 PITCH, 13T, 0° angle 2 mm bore, BRASS (This is press-on style pinion gear) - #DB501-13
DUBICK PINION 48 PITCH, 13T, 0° angle 2 mm bore, BRASS
This is press-on style pinion gear
-
DUBICK PINION 48 PITCH, 14T, 0° angle, 3 mm bore, BRASS (This is press-on style pinion gear) - #DB501-14
DUBICK PINION 48 PITCH, 14T, 0° angle, 3 mm bore, BRASS
This is press-on style pinion gear
-
DUBICK PINION 48 PITCH, 15T, 0° angle, BRASS (This is press-on style pinion gear) - #DB501-15
DUBICK PINION 48 PITCH, 15T, 0° angle, BRASS (This is press-on style pinion gear) - #501-15
This is press-on style pinion gear!
-
DUBICK PINION 48 PITCH, 16T, 0° angle, BRASS (This is press-on style pinion gear) - #DB501-16
DUBICK PINION 48 PITCH, 16T, 0° angle, BRASS (This is press-on style pinion gear) - #501-16
This is press-on style pinion gear!
-
DUBICK armature bronze spacers 4.6 mm thick, 2 pcs. - #DB4034
DUBICK armature bronze spacers 4.6 mm thick, 2 pcs. - #DB4034
-
DUBICK 2 mm, .22" (5,5 mm) thick aluminium axle spacer, 1 pc. - #DB712-5.5
DUBICK 2 mm, .22" (5,5 mm) thick aluminium axle spacer, 1 pc. - #DB712-5.5
-
DUBICK 2 mm, .24" (6 mm) thick aluminium axle spacer, 1 pc. - #DB712-6
DUBICK 2 mm, .24" (6 mm) thick aluminium axle spacer, 1 pc. - #DB712-6
-
DUBICK 2 mm, .26" (6,5 mm) thick aluminium axle spacer, 1 pc. - #DB712-6.5
DUBICK 2 mm, .26" (6,5 mm) thick aluminium axle spacer, 1 pc. - #DB712-6.5
-
DUBICK JK style body mounting clips, pair - #DB601
DUBICK JK style body mounting clips, pair - #DB601
Body mounting clip - same size as JK 9008
-
DUBICK 2 mm, .28" (7 mm) thick aluminium axle spacer, 1 pc. - #DB712-7
DUBICK 2 mm, .28" (7 mm) thick aluminium axle spacer, 1 pc. - #DB712-7
-
DUBICK Set #1 of 2 mm inside diameter aluminium tubes ( 5.5 mm (.22"), 6 mm (.24"), 6.5 mm (.26"), 7 mm (.28")) - #DB712
DUBICK Set of 2 mm inside diameter aluminium tubes - #DB712
In set 1 pc of each size: 5.5 mm (.22"), 6 mm (.24"), 6.5 mm (.26"), 7 mm (.28")